Lexus ES: Hybrid/EV Battery Energy Control Module EEPROM Data Memory Failure (P062F44)
DESCRIPTION
The battery ECU assembly monitors its internal operation and will store these DTCs when it detects an internal malfunction. If these DTCs are output, replace the battery ECU assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P062F44 | Hybrid/EV Battery Energy Control Module EEPROM Data Memory Failure | ECU internal malfunction (1 trip detection logic) | Battery ECU assembly | Comes on | Master Warning Light: Does not come on |
MONITOR DESCRIPTION
The battery ECU assembly monitors its internal operation. If the internal operation is malfunctioning, the battery ECU assembly illuminates the MIL and stores a DTC.
MONITOR STRATEGY
| Related DTCs | P062F (INF P062F44): Internal control module EEPROM (battery energy control module) |
| Required sensors/components | Battery ECU assembly |
| Frequency of operation | Continuous |
| Duration | TMC's intellectual property |
| MIL operation | Immediately |
| Sequence of operation | None |
TYPICAL ENABLING CONDITIONS
| The monitor will run whenever the following DTCs are not stored | TMC's intellectual property |
| Other conditions belong to TMC's intellectual property | - |
TYPICAL MALFUNCTION THRESHOLDS
| TMC's intellectual property | - |
COMPONENT OPERATING RANGE
| Battery ECU assembly | DTC P062F (INF P062F44) is not detected |
CONFIRMATION DRIVING PATTERN
HINT:
-
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here
.gif)
-
When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG) and turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the power switch off and wait for 2 minutes or more.
- Turn the power switch on (IG) and turn the Techstream on.
-
With power switch on (IG) and wait for 30 seconds or more.[*1]
HINT:
[*1]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- Enter the following menus: Powertrain / HV Battery / Utility / All Readiness.
-
Check the DTC judgment result.
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE or N/A, perform the normal judgment procedure again.
PROCEDURE
| 1. | REPLACE BATTERY ECU ASSEMBLY |
Click here
| NEXT | .gif) | END |
READ NEXT:
Hybrid/EV Battery Energy Control Module EEPROM Calibration / Parameter Memory Failure (P062F46)
DESCRIPTION The battery ECU assembly monitors its internal operation and will store these DTCs when it detects an internal malfunction. If these DTCs are output, replace the battery ECU assembly. D
Hybrid/EV Powertrain Control Module Unexpected Operation (P0A1D94)
DESCRIPTION The battery ECU assembly monitors the hybrid vehicle control ECU via CAN communication. If the battery ECU assembly detects that the hybrid vehicle control ECU is malfunctioning, it will i
Hybrid/EV Battery Cooling Fan 1 Circuit Short to Ground (P0A8111)
DESCRIPTION The battery cooling blower assembly speed is controlled by the battery ECU assembly. Power is supplied to the battery cooling blower assembly when the MREL terminal of the hybrid vehicle c
SEE MORE:
Rain Sensor Malfunction (B1400)
DESCRIPTION This DTC is stored when the rain sensor detects an internal malfunction. DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from B1400 Rain Sensor Malfunction
IG power source voltage is 9.5 V or more
Either of the following is dete
Parts Location
PARTS LOCATION ILLUSTRATION *1 FRONT ENGINE MOUNTING INSULATOR *2 REAR ENGINE MOUNTING INSULATOR *3 CANISTER *4 FUEL PUMP (for Low Pressure Side) *5 MASS AIR FLOW METER SUB-ASSEMBLY *6 PARK / NEUTRAL POSITION SWITCH ASSEMBLY *7 VACUUM SWITCHING VALVE (for Active C
