Lexus ES manuals

Lexus ES: Hybrid/EV Battery Energy Control Module EEPROM Calibration / Parameter Memory Failure (P062F46)

Lexus ES (XZ10) Service Manual / Engine & Hybrid System / Hybrid / Battery Control / Hybrid Battery System (for Lithium-ion Battery) / Hybrid/EV Battery Energy Control Module EEPROM Calibration / Parameter Memory Failure (P062F46)

DESCRIPTION

The battery ECU assembly monitors its internal operation and will store these DTCs when it detects an internal malfunction. If these DTCs are output, replace the battery ECU assembly.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Warning Indicate

P062F46

Hybrid/EV Battery Energy Control Module EEPROM Calibration / Parameter Memory Failure

ECU internal malfunction

(EEPROM error)

(1 trip detection logic)

Battery ECU assembly

Comes on

Master Warning Light:

Comes on

MONITOR DESCRIPTION

The battery ECU assembly monitors its internal operation. If the internal operation is malfunctioning, the battery ECU assembly illuminates the MIL and stores a DTC.

MONITOR STRATEGY

Related DTCs

P062F (INF P062F46): Internal control module EEPROM (battery energy control module)

Required sensors/components

Battery ECU assembly

Frequency of operation

Continuous

Duration

TMC's intellectual property

MIL operation

1 driving cycle

Sequence of operation

None

TYPICAL ENABLING CONDITIONS

The monitor will run whenever the following DTCs are not stored

TMC's intellectual property

Other conditions belong to TMC's intellectual property

-

TYPICAL MALFUNCTION THRESHOLDS

TMC's intellectual property

-

COMPONENT OPERATING RANGE

Battery ECU assembly

DTC P062F (INF P062F46) is not detected

CONFIRMATION DRIVING PATTERN

HINT:

  • After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

    Click here

  • When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.

    Click here

  1. Connect the Techstream to the DLC3.
  2. Turn the power switch on (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the power switch off and wait for 2 minutes or more.
  5. Turn the power switch on (IG) and turn the Techstream on.
  6. With power switch on (IG) and wait for 2 minutes or more.[*1]

    HINT:

    [*1]: Normal judgment procedure.

    The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.

  7. Enter the following menus: Powertrain / HV Battery / Utility / All Readiness.
  8. Check the DTC judgment result.

    HINT:

    • If the judgment result shows NORMAL, the system is normal.
    • If the judgment result shows ABNORMAL, the system has a malfunction.
    • If the judgment result shows INCOMPLETE or N/A, perform the normal judgment procedure again.

PROCEDURE

1.

REPLACE BATTERY ECU ASSEMBLY

Click here

NEXT

END

READ NEXT:

 Hybrid/EV Powertrain Control Module Unexpected Operation (P0A1D94)

DESCRIPTION The battery ECU assembly monitors the hybrid vehicle control ECU via CAN communication. If the battery ECU assembly detects that the hybrid vehicle control ECU is malfunctioning, it will i

 Hybrid/EV Battery Cooling Fan 1 Circuit Short to Ground (P0A8111)

DESCRIPTION The battery cooling blower assembly speed is controlled by the battery ECU assembly. Power is supplied to the battery cooling blower assembly when the MREL terminal of the hybrid vehicle c

 Hybrid/EV Battery Cooling Fan 1 Circuit Short to Auxiliary Battery or Open (P0A8115)

DESCRIPTION Refer to the description for DTC P0A8111. Click here DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate P0A8115 Hybrid/EV Battery Cooling

SEE MORE:

 How To Proceed With Troubleshooting

CAUTION / NOTICE / HINT HINT: Use the following procedure to troubleshoot the lighting system. *: Use the Techstream. PROCEDURE 1. VEHICLE BROUGHT TO WORKSHOP NEXT 2. CUSTOMER PROBLEM ANALYSIS HINT: In troubleshooting, confirm that the problem symptoms h

 Drive Motor "A" Inverter Stuck On (P0A789E,P1C5D19)

DTC SUMMARY MALFUNCTION DESCRIPTION This DTC indicates that a large current flowed through the motor inverter. The cause of this malfunction may be one of the following: Area Main Malfunction Description Hybrid vehicle transaxle assembly Open or short circuit in the motor coils Motor

© 2016-2024 Copyright www.lexguide.net