Lexus ES: How To Proceed With Troubleshooting
CAUTION / NOTICE / HINT
HINT:
- Use the following procedure to troubleshoot the panoramic moon roof system.
- *: Use the Techstream.
PROCEDURE
| 1. | VEHICLE BROUGHT TO WORKSHOP |
|
.gif)
| 2. | CUSTOMER PROBLEM ANALYSIS |
HINT:
- In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
- Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
-
The following 5 items are important points for problem analysis:
What
Vehicle model, system name
When
Date, time, occurrence frequency
Where
Road conditions
Under what conditions?
Driving conditions, weather conditions
How did it happen?
Problem symptoms
|
| 3. | PRE-CHECK |
(a) Measure the battery voltage.
Standard Voltage:
11 to 14 V
If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.
(b) Check the fuses and relays.
(c) Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.
|
| 4. | CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM* |
(a) Using the Techstream, check for CAN communication system DTCs.
Click here .gif)
| Result | Proceed to |
|---|---|
| CAN DTCs are not output | A |
| CAN DTCs are output | B |
| B | .gif) | GO TO CAN COMMUNICATION SYSTEM |
|
| 5. | CHECK COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM* |
(a) Using the Techstream, check for LIN communication system DTCs.
Click here
| Result | Proceed to |
|---|---|
| LIN DTCs are not output | A |
| LIN DTCs are output | B |
| B | | GO TO LIN COMMUNICATION SYSTEM |
|
| 6. | CHECK FOR DTC* |
(a) Check for DTCs and make a note of any codes that are output.
Click here
(b) Clear the DTCs.
Body Electrical > Sliding Roof > Clear DTCs(c) Recheck for DTCs.
Body Electrical > Sliding Roof > Trouble Codes| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
| B | | GO TO DIAGNOSTIC TROUBLE CODE CHART |
|
| 7. | PROBLEM SYMPTOMS TABLE |
(a) Refer to Problem Symptoms Table.
Click here
| Result | Proceed to |
|---|---|
| Fault is not listed in Problem Symptoms Table | A |
| Fault is listed in Problem Symptoms Table | B |
| B | | GO TO STEP 9 |
|
| 8. | OVERALL ANALYSIS AND TROUBLESHOOTING* |
(a) Operation Check
Click here
(b) Terminals of ECU
Click here
(c) Data List / Active Test
Click here
(d) Inspection
Click here
|
| 9. | ADJUST, REPAIR OR REPLACE |
(a) Check if the sliding roof ECU (sliding roof drive gear assembly) or roof sunshade ECU (sliding roof drive gear assembly) has been replaced, or the sliding roof glass sub-assembly, sliding roof housing panel, slide roof rail sub-assembly or sunshade trim sub-assembly has been adjusted, or removed and installed.
| Result | Proceed to |
|---|---|
| The sliding roof ECU (sliding roof drive gear assembly) or roof sunshade ECU (sliding roof drive gear assembly) has been replaced, or the sliding roof glass sub-assembly, sliding roof housing panel, slide roof rail sub-assembly or sunshade trim sub-assembly has been adjusted, or removed and installed | A |
| The sliding roof ECU (sliding roof drive gear assembly) and roof sunshade ECU (sliding roof drive gear assembly) have not been replaced, and the sliding roof glass sub-assembly, sliding roof housing panel, slide roof rail sub-assembly and sunshade trim sub-assembly have not been adjusted, or removed and installed | B |
| B | | GO TO STEP 11 |
|
| 10. | INITIALIZE PANORAMIC MOON ROOF SYSTEM |
(a) Initialize the sliding roof ECU (sliding roof drive gear assembly).
Click here
(b) Initialize the roof sunshade ECU (sliding roof drive gear assembly).
Click here
|
| 11. | CONFIRMATION TEST |
| NEXT | | END |
READ NEXT:
Operation Check
OPERATION CHECK CHECK AUTO OPERATION FUNCTION (FOR SLIDING ROOF) NOTICE:
Make sure that initialization has been completed before performing this inspection.
Click here
The sliding roof auto ope
Customize Parameters
CUSTOMIZE PARAMETERS CUSTOMIZE PANORAMIC MOON ROOF SYSTEM NOTICE:
When the customer requests a change in a function, first make sure that the function can be customized.
Be sure to make notes of
Initialization
INITIALIZATION INITIALIZE PANORAMIC MOON ROOF SYSTEM (FOR SLIDING ROOF) NOTICE:
When the sliding roof glass sub-assembly, sliding roof housing panel or slide roof rail sub-assembly is adjusted or r
SEE MORE:
Components
COMPONENTS ILLUSTRATION *1 COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY *2 FRONT WIPER ARM AND BLADE ASSEMBLY LH *3 FRONT WIPER ARM AND BLADE ASSEMBLY RH *4 FRONT WIPER ARM HEAD CAP *5 NO. 2 COWL TOP PANEL INSULATOR *6 NO. 3 COWL TOP PANEL INSULATOR *7 WINDSHIELD OUTSI
Diameter of the Tire is not Uniform (C1337)
DESCRIPTION The 4WD ECU assembly outputs this DTC if a difference in tire size is detected. DTC No. Detection Item DTC Detection Condition Trouble Area C1337 Diameter of the Tire is not Uniform When the following continues for 36 seconds or more: At a vehicle speed of 30 km/h (19 mp
