Lexus ES: Glass Position Initialization Incomplete (B2313)
DESCRIPTION
The power window regulator motor assemblies are operated by the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assemblies. The power window regulator motor assembly has motor, regulator and ECU functions.
When the ECU built into a power window regulator motor assembly determines that the power window regulator motor assembly has not been initialized, DTC B2313 is stored.
D-Door Motor| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2313 | Glass Position Initialization Incomplete |
|
|
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2313 | Glass Position Initialization Incomplete |
|
|
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2313 | Glass Position Initialization Incomplete |
|
|
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2313 | Glass Position Initialization Incomplete |
|
|
CAUTION / NOTICE / HINT
NOTICE:
- DTC B2313 is stored in each power window regulator motor assembly.
- If the battery is disconnected while the engine switch is on (IG), DTC B2313 will be stored.
-
If a power window regulator motor assembly has been replaced with a new one, initialize the power window control system.
Click here
.gif)
PROCEDURE
| 1. | PERFORM INITIALIZATION (APPLICABLE LOCATION) |
(a) Turn the engine switch on (IG).
(b) Initialize the power window regulator motor assembly.
Click here
HINT:
Initialize the power window regulator motor assembly that has DTC B2313 stored in its ECU.
|
| 2. | CHECK DTC OUTPUT |
(a) Turn the engine switch off.
(b) Wait for at least 10 seconds, and then turn the engine switch on (IG).
(c) Check for DTCs.
Body Electrical > D-Door Motor > Trouble Codes Body Electrical > P-Door Motor > Trouble Codes Body Electrical > RL-Door Motor > Trouble Codes Body Electrical > RR-Door Motor > Trouble CodesHINT:
Check for DTCs for the power window regulator motor assembly that had DTC B2313 stored in its ECU.
OK:
DTC B2313 is not output.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Driver door power window) | B |
| NG (Front passenger door power window) | |
| NG (Rear LH door power window) | C |
| NG (Rear RH door power window) |
| A |  | END (POWER WINDOW CONTROL SYSTEM HAS NOT BEEN INITIALIZED) |
| B | | REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door or Front Passenger Door) |
| C | | REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door or Rear RH Door) |
READ NEXT:
Remote Up / Down Function does not Operate
DESCRIPTION When the engine switch on (IG), the multiplex network master switch assembly sends remote up and down signals to each power window regulator motor assembly via LIN communication. WIRING DI
Driver Side Power Window does not Operate with Power Window Master Switch
DESCRIPTION When the engine switch is on (IG), the power window regulator motor assembly (for driver door) is operated by the multiplex network master switch assembly. The power window regulator motor
Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch
DESCRIPTION When the engine switch is on (IG), the power window regulator motor assembly (for front passenger door) is operated by the power window regulator switch assembly. The power window regulato
SEE MORE:
Components
COMPONENTS ILLUSTRATION *1 BATTERY CLAMP SUB-ASSEMBLY - - N*m (kgf*cm, ft.*lbf): Specified torque - - ILLUSTRATION *1 TRANSMISSION CONTROL CABLE ASSEMBLY *2 TRANSMISSION CONTROL SHAFT LEVER *3 PARK/NEUTRAL POSITION SWITCH ASSEMBLY *4 WASHER Tighteni
Inspection
INSPECTION PROCEDURE 1. INSPECT PCV VALVE (VENTILATION VALVE SUB-ASSEMBLY) (a) Install a hose to the PCV valve (ventilation valve sub-assembly). (b) Check PCV valve (ventilation valve sub-assembly) operation. (1) Blow air into the cylinder head sub-assembly side, and check that air passes through ea
