Lexus ES: Fuel Rail / System Pressure - Too Low (P008700)

Lexus ES (XZ10) Service Manual / Engine & Hybrid System / A25a-fxs (engine Control) / Sfi System / Fuel Rail / System Pressure - Too Low (P008700)

DESCRIPTION

The high-pressure direct injection fuel system consists of a spill control valve, check valve, fuel relief valve, fuel pressure sensor (for high pressure side), fuel pump assembly (for high pressure side) and direct fuel injector assemblies. The spill control valve adjusts the return volume of high-pressure fuel. The check valve mechanically opens and closes the path to the fuel delivery pipe. The relief valve releases the fuel back to the fuel tank if there is a malfunction in the high-pressure fuel system. The fuel pump assembly (for high pressure side) is installed to the cylinder head cover and operated by a cam installed to the end of the exhaust camshaft. Rotation of the camshaft moves the pump plunger inside the fuel pump assembly (for high pressure side) up and down, pressurizing the fuel. The pressurized fuel opens the check valve and is pumped into the fuel delivery pipe. The ECM controls the spill control valve to adjust the fuel pressure between 3.0 and 25 MPa (31 and 255 kgf/cm2, 435 and 3625 psi) and monitors signals from the fuel pressure sensor (for high pressure side) to maintain the target fuel pressure.

DTC No.	Detection Item	DTC Detection Condition	Trouble Area	MIL	Memory	Note
P008700	Fuel Rail / System Pressure - Too Low	Although the ECM is not requesting the fuel pump assembly (for high pressure side) to open the spill control valve, fuel pressure decreases 5 MPa (51.0 kgf/cm2, 725 psi) from target pressure for about 6 seconds (1 trip detection logic).	Leak of fuel Fuel pipe (fuel tank - fuel pump assembly (for high pressure side)) Fuel pipe (fuel pump assembly (for high pressure side) - direct fuel injector assembly) Direct fuel injector assembly Fuel pump assembly (for high pressure side) Fuel pump (for low pressure side) Fuel pressure sensor (for high pressure side) Fuel system ECM	Comes on	DTC stored	SAE Code: P0087

MONITOR DESCRIPTION

If the fuel pressure (for high pressure side) decreases despite an increase request signal being sent to the fuel pump assembly (for high pressure side) by the ECM, the ECM will illuminate the MIL and store this DTC.

MONITOR STRATEGY

Related DTCs	P0087: Fuel pressure too low
Required Sensors/Components (Main)	Fuel pressure sensor (for high pressure side)
Required Sensors/Components (Related)	-
Frequency of Operation	Continuous
Duration	About 6 seconds
MIL Operation	Immediate
Sequence of Operation	None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever the following DTCs are not stored	None
Time after engine start	0.2 seconds or more
Time after fuel cut finished	3 seconds or more
Target fuel pressure	Small change
Injection mode	Direct injection or dual injection

TYPICAL MALFUNCTION THRESHOLDS

Both of the following conditions are met	-
Difference in fuel pressure between actual and target	Less than -5 MPa (-51.0 kgf/cm2, -725 psi)
Actual discharge rate of high pressure fuel pump	240 mm3/st or more

CONFIRMATION DRIVING PATTERN

HINT:

When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here
Permanent misfire and fuel system DTCs can only be cleared when performing the universal trip driving pattern when no malfunction is detected.

Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Record the Freeze Frame Data.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG).
Turn the Techstream on.
Put the engine in Inspection Mode (Maintenance Mode).
Click here
Start the engine.
Based on the engine speed, engine load, injection mode and other conditions displayed in the Freeze Frame Data, reproduce the conditions present when the DTC was stored.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the pending DTCs.
HINT:
- If a pending DTC is output, the system is malfunctioning.
- If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P008700.

Check the DTC judgment result.

Techstream Display	Description
NORMAL	DTC judgment completed System normal
ABNORMAL	DTC judgment completed System abnormal
INCOMPLETE	DTC judgment not completed Perform driving pattern after confirming DTC enabling conditions

HINT:

If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system has a malfunction.

CAUTION / NOTICE / HINT

NOTICE:

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the Freeze Frame Data and Vehicle Control History can be useful for troubleshooting.
Click here

(Select Powertrain in Health Check and then check the time stamp data.)

Click here
If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.
Click here

HINT:

Read Freeze Frame Data using the Techstream. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE

1.	CHECK FUEL LEAK

(a) Check around and beneath the vehicle for fuel leaks, fumes, etc.

OK:

No fuel leaks present.

REPAIR OR REPLACE FUEL LEAK POINT

2.	CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P008700)

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(d) Enter the following menus: Powertrain / Engine / Trouble Codes.

(e) Read the DTCs.

Powertrain > Engine > Trouble Codes

Result	Proceed to
DTC P008700 is output	A
DTC P008700 and other DTCs are output	B

HINT:

If any DTCs other than P008700 are output, troubleshoot those DTCs first.

GO TO DTC CHART

3.	CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST

(a) Has the vehicle run out of fuel in the past?

YES

DTC CAUSED BY RUNNING OUT OF FUEL

4.	CHECK MISFIRE COUNT OF DIRECT INJECTION

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(d) Put the engine in Inspection Mode (Maintenance Mode).

Powertrain > Hybrid Control > Utility

Tester Display
Inspection Mode

(e) Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

(f) Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Mode / Data List / Coolant Temperature, Injection Mode and Misfire Count Cylinder #1 to Misfire Count Cylinder #4.

Powertrain > Engine > Active Test

Active Test Display
Control the Injection Mode

Data List Display
Coolant Temperature
Injection Mode
Misfire Count Cylinder #1
Misfire Count Cylinder #2
Misfire Count Cylinder #3
Misfire Count Cylinder #4

(g) According to the display on the Techstream, read the Data List with the Active Test "Control the Injection Mode" set to Direct.

Injection Mode	Misfire Count	Proceed to
Direct	There are no misfire counts	A
	3 cylinders or more have misfire counts	A
	1 or 2 cylinders have misfire counts	B

HINT:

Perform "Inspection After Repair" after replacing the direct fuel injector assembly.

Click here

REPLACE DIRECT FUEL INJECTOR ASSEMBLY

5.	INSPECT FUEL PRESSURE SENSOR (FOR HIGH PRESSURE SIDE)

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(d) Put the engine in Inspection Mode (Maintenance Mode).

Powertrain > Hybrid Control > Utility

Tester Display
Inspection Mode

(e) Start the engine.

(f) Enter the following menus: Powertrain / Engine / Data List / Fuel Pressure (High).

Powertrain > Engine > Data List

Tester Display
Fuel Pressure (High)

(g) Check that the fuel pressure fluctuates when the engine condition changes from idling to racing.

Result	Proceed to
Fuel pressure does not rise	A
Fuel pressure does not fluctuate	B
Fuel pressure fluctuates	C

HINT:

Perform "Inspection After Repair" after replacing the fuel pressure sensor (for high pressure side).

Click here

REPLACE FUEL PRESSURE SENSOR (FOR HIGH PRESSURE SIDE)

GO TO STEP 8

6.	CHECK FUEL PUMP OPERATION (FOR LOW PRESSURE SIDE)

(a) Check the fuel pump operation (for low pressure side).

Click here

HINT:

Perform "Inspection After Repair" after replacing the Fuel pump (for low pressure side).

Click here

REPLACE FUEL PUMP (FOR LOW PRESSURE SIDE)

7.	CHECK FUEL PRESSURE (FOR LOW PRESSURE SIDE)

(a) Check the fuel pressure (for low pressure side).

Click here

REPAIR OR REPLACE FUEL SYSTEM

8.	REPLACE FUEL PUMP ASSEMBLY (FOR HIGH PRESSURE SIDE)

(a) Replace the fuel pump assembly (for high pressure side).

Click here

HINT:

Perform "Inspection After Repair" after replacing the fuel pump assembly (for high pressure side).

Click here

CLEAR DTC

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(d) Clear the DTCs.

Powertrain > Engine > Clear DTCs

(e) Turn the power switch off and wait for at least 30 seconds.

10.	CHECK IF DTC OUTPUT RECURS (SEE IF DTC P008700 IS OUTPUT AGAIN)

(a) Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

(b) Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes

Result	Proceed to
DTCs are not output	A
DTC P008700 is output	B

END

REPLACE ECM

SEE MORE:

Inspection

INSPECTION PROCEDURE 1. INSPECT PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (a) Using a dial indicator, measure the runout of the rear propeller shaft assembly (for front side). Maximum Runout: 0.6 mm (0.0236 in.) NOTICE: The dial indicator must be set at a right angle to the center of the rear

System Diagram

SYSTEM DIAGRAM ELECTRICAL REMOTE CONTROL MIRROR FUNCTION MIRROR HEATER FUNCTION AUTOMATIC GLARE-RESISTANT EC MIRROR FUNCTION Communication Table Sender Receiver Signal Communication Method Air Conditioning Control Assembly Air Conditioning Amplifier Assembly Mirror heater switch

Lexus ES: Fuel Rail / System Pressure - Too Low (P008700)

READ NEXT:

Fuel Rail / System Pressure - Too High (P008800)

Low Pressure Fuel System Pressure - Too Low (P008A00)

Low Pressure Fuel System Pressure - Too High (P008B00)

SEE MORE:

Inspection

System Diagram