Lexus ES: Checking Monitor Status
CHECKING MONITOR STATUS
The purpose of the monitor result (mode 06) is to allow access to the results of on-board diagnostic monitoring tests of specific components/systems that are not continuously monitored. Examples are catalysts and evaporative emissions (EVAP) systems.
The monitor result allows the OBD II scan tool to display the monitor status, test value, minimum test limit and maximum test limit. These data are displayed after the vehicle has been driven to run the monitor.
When the test value is not between the minimum and maximum test limits, the ECM (PCM) interprets this as a malfunction. If the test value is on the borderline of the test limits, the component is likely to malfunction in the near future.
Perform the following procedures to view the monitor status. Although these procedures refer to the Lexus/Toyota Techstream, the monitor status can be checked using a generic OBD II scan tool. Refer to your scan tool operator's manual for specific procedural information.
PERFORM MONITOR DRIVE PATTERN
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Clear the DTCs.
Powertrain > Engine > Clear DTCs(e) Operate the vehicle in accordance with the applicable drive pattern described in Readiness Monitor Drive Pattern. Do not turn the power switch off.
Click here .gif)
NOTICE:
The test results will be lost if the power switch is turned off.
ACCESS MONITOR RESULT
(a) Enter the following menus: Powertrain / Engine / Monitor / Current Monitor / Result.
Powertrain > Engine > Monitor(b) Confirm the monitor status for each component.
HINT:
The monitor status for each component is displayed in the Result column.
- Pass: The component is functioning normally.
- Fail: The component is malfunctioning.
(c) Display the test results and test values for a monitor by selecting the icon in the Details column for that monitor.
CHECK COMPONENT STATUS
(a) Compare the Test Value with the minimum test limit (Min Limit) and maximum test limit (Max Limit).
(b) If the Test Value is between the minimum and maximum test limits, the component is functioning normally. If not, the component is malfunctioning. The test value is usually not near the test limits.
If the test value is on the borderline of the test limits, the component is likely to malfunction in the near future.
HINT:
The monitor result might on rare occasions be Pass even if the Malfunction Indicator Lamp (MIL) is illuminated. This indicates the system malfunctioned on a previous driving cycle. This might be caused by an intermittent problem.
MONITOR RESULT INFORMATION
When using a generic scan tool, multiply the test value by the scaling value.
Refer to "Monitor Result" in each DTC related to the monitor.
Click here
READ NEXT:
Readiness Monitor Drive Pattern
READINESS MONITOR DRIVE PATTERN PURPOSE OF READINESS TESTS
The On-Board Diagnostic (OBD II) system is designed to monitor the performance of emission related components, and indicate any detected a
Problem Symptoms Table
PROBLEM SYMPTOMS TABLE HINT:
Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of
Problem Symptoms Table
PROBLEM SYMPTOMS TABLE HINT:
Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of
SEE MORE:
Installation
INSTALLATION CAUTION / NOTICE / HINT HINT:
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
PROCEDURE 1. PRECAUTION NOTICE: After turning the engine switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required bef
Parts Location
PARTS LOCATION ILLUSTRATION *1 SWING GRILLE ACTUATOR ASSEMBLY *2 RADIATOR SHUTTER SUB-ASSEMBLY *3 ECM - - ILLUSTRATION *1 COMBINATION METER ASSEMBLY *2 INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ECU-B NO. 2 FUSE *3 AIR CONDITIONING AMPLIFIER ASSEMBLY *4 HYB
