Lexus ES: Terminals Of Ecu
TERMINALS OF ECU
CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
| *A | w/o Seat Heater | *B | w/ Seat Heater |
(a) Disconnect the G39 air conditioning amplifier assembly connector.
(b) Measure the voltage and resistance according to the value(s) in the table below.
HINT:
Measure the values on the wire harness side with the connector disconnected.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G39-2 (IG+) - G39-4 (GND) | R - W-B | Power source (IG) | Engine switch on (IG) | 11 to 14 V |
| G39-2 (IG+) - G39-4 (GND) | R - W-B | Power source (IG) | Engine switch off | Below 1 V |
| G39-1 (B) - G39-4 (GND) | B - W-B | Battery power supply | Always | 11 to 14 V |
| G39-4 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
(c) Reconnect the G39 air conditioning amplifier assembly connector.
(d) Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G39-5 (RDFG) - G39-4 (GND) | R - W-B | Rear window defogger signal | Engine switch on (IG), rear window defogger switch off | 11 to 14 V |
| G39-5 (RDFG) - G39-4 (GND) | R - W-B | Rear window defogger signal | Engine switch on (IG), rear window defogger switch on | Below 1 V |
| G39-14 (LIN1) - G39-4 (GND) | BE - W-B | LIN communication line | Engine switch on (IG) | Pulse generation |
CHECK REAR WINDOW DEFOGGER SWITCH (AIR CONDITIONING CONTROL ASSEMBLY)
(a) Disconnect the G23 air conditioning control assembly connector.
(b) Measure the voltage and resistance according to the value(s) in the table below.
HINT:
Measure the values on the wire harness side with the connector disconnected.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G23-8 (IG+) - G23-4 (E) | R - W-B | Power source (IG) | Engine switch on (IG) | 11 to 14 V |
| G23-8 (IG+) - G23-4 (E) | R - W-B | Power source (IG) | Engine switch off | Below 1 V |
| G23-4 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
(c) Reconnect the G23 air conditioning control assembly connector.
(d) Check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G23-3 (LIN1) - G23-4 (E) | LG - W-B | LIN communication line | Engine switch on (IG) | Pulse generation |
READ NEXT:
Diagnosis System
DIAGNOSIS SYSTEM CHECK DLC3 (a) Check the DLC3. Click here INSPECT BATTERY VOLTAGE (a) Measure the battery voltage. Standard Voltage: 11 to 14 V If the voltage is below 11 V, recharge or replace th
Data List / Active Test
DATA LIST / ACTIVE TEST ACTIVE TEST HINT: Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive func
Rear Window Defogger System does not Operate
DESCRIPTION When the rear window defogger switch on the air conditioning control assembly is pressed, the operation signal is transmitted to the air conditioning amplifier assembly via LIN communicati
SEE MORE:
Components
COMPONENTS ILLUSTRATION *1 CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY *2 INSTRUMENT PANEL FINISH PANEL END LH *3 INSTRUMENT PANEL FINISH PANEL END RH *4 REAR UPPER CONSOLE PANEL SUB-ASSEMBLY *5 SHIFT LEVER KNOB SUB-ASSEMBLY *6 UPPER CONSOLE PANEL SUB-ASSEMBLY
Installation
INSTALLATION PROCEDURE 1. INSTALL NO. 1 MOTOR COOLING HOSE HINT: Perform this procedure only when replacement of the motor cooling cooler is necessary. (a) Coat the pipe of the motor cooling cooler with a small amount of ATF as shown in the illustration. ATF Application Area (b) Install th
