Lexus ES manuals

Lexus ES: Switch Failure (B2342)

DESCRIPTION

This DTC is stored when the sliding roof ECU (sliding roof drive gear sub-assembly) detects that the sliding roof switch (map light sub-assembly) is stuck for 30 seconds or more.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

B2342

Switch Failure

Sliding roof ECU (sliding roof drive gear sub-assembly) detects sliding roof switch (map light sub-assembly) is stuck for 30 seconds or more

  • Sliding roof ECU (Sliding roof drive gear sub-assembly)
  • Sliding roof switch (Map light sub-assembly)
  • Wire harness or connector

WIRING DIAGRAM

Refer to DTC B2341.

Click here

CAUTION / NOTICE / HINT

NOTICE:

  • If the sliding roof ECU (sliding roof drive gear sub-assembly) is removed and reinstalled or replaced, the sliding roof ECU (sliding roof drive gear sub-assembly) must be initialized.

    Click here

PROCEDURE

1.

READ VALUE USING TECHSTREAM

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Sliding Roof / Data List.

(e) Read the Data List according to the display on the Techstream.

Body Electrical > Sliding Roof > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Open Switch Failure(Past)

Open switch failure signal (Past)

OFF or ON

OFF: No sliding roof open switch failure signal (Past)

ON: Sliding roof open switch failure signal (Past)

-

Close Switch Failure(Past)

Close switch failure signal (Past)

OFF or ON

OFF: No sliding roof close switch failure signal (Past)

ON: Sliding roof close switch failure signal (Past)

-

Up Switch Failure(Past)

Up switch failure signal (Past)

OFF or ON

OFF: No sliding roof tilt up switch failure signal (Past)

ON: Sliding roof tilt up switch failure signal (Past)

-

Down Switch Failure(Past)

Down switch failure signal (Past)

OFF or ON

OFF: No sliding roof tilt down switch failure signal (Past)

ON: Sliding roof tilt down switch failure signal (Past)

-

Open Switch Failure(Current)

Open switch failure signal (Current)

OFF or ON

OFF: No sliding roof open switch failure signal (Current)

ON: Sliding roof open switch failure signal (Current)

-

Close Switch Failure(Current)

Close switch failure signal (Current)

OFF or ON

OFF: No sliding roof close switch failure signal (Current)

ON: Sliding roof close switch failure signal (Current)

-

Up Switch Failure(Current)

Up switch failure signal (Current)

OFF or ON

OFF: No sliding roof tilt up switch failure signal (Current)

ON: Sliding roof tilt up switch failure signal (Current)

-

Down Switch Failure(Current)

Down switch failure signal (Current)

OFF or ON

OFF: No sliding roof tilt down switch failure signal (Current)

ON: Sliding roof tilt down switch failure signal (Current)

-

Body Electrical > Sliding Roof > Data List

Tester Display

Open Switch Failure(Past)

Close Switch Failure(Past)

Up Switch Failure(Past)

Down Switch Failure(Past)

Open Switch Failure(Current)

Close Switch Failure(Current)

Up Switch Failure(Current)

Down Switch Failure(Current)

OK:

OFF is displayed for each Data List item.

OK

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

NG

2.

CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) - BODY GROUND)

(a) Disconnect the P22 sliding roof ECU (sliding roof drive gear sub-assembly) connector.

(b) Disconnect the P13 sliding roof switch (map light sub-assembly) connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

P22-10 (OPN) or P13-11 (OPN) - Body ground

Always

10 kΩ or higher

P22-8 (CLS) or P13-12 (CLS) - Body ground

Always

10 kΩ or higher

P22-5 (UP) or P13-23 (UP) - Body ground

Always

10 kΩ or higher

P22-9 (DWN) or P13-24 (DOWN) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

3.

INSPECT SLIDING ROOF SWITCH (MAP LIGHT SUB-ASSEMBLY)

(a) Remove the sliding roof switch (map light sub-assembly).

Click here

(b) Inspect the sliding roof switch (map light sub-assembly).

Click here

OK

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

NG

REPLACE SLIDING ROOF SWITCH (MAP LIGHT SUB-ASSEMBLY)

READ NEXT:

 Position Initialization Incomplete (B2343)

DESCRIPTION This DTC is stored when the sliding roof ECU (sliding roof drive gear sub-assembly) has not been initialized. DTC No. Detection Item DTC Detection Condition Trouble Area B2343

 Remote Control System does not Operate

DESCRIPTION The main body ECU (multiplex network body ECU) receives remote control signals from the driver door key cylinder or electrical key transmitter sub-assembly. Then, the main body ECU (multip

 Key-off Operation Function Operates even if Operating Conditions are not Satisfied

DESCRIPTION The sliding roof ECU (sliding roof drive gear sub-assembly) operates its built-in motor according to the sliding roof switch (map light sub-assembly) operation. Using the sliding roof swit

SEE MORE:

 ABS Pump Motor Control Circuit Short to Ground (C052C11,C052C13,C142719)

DESCRIPTION The ABS motor relay is built into the brake actuator assembly. When the skid control ECU (brake actuator assembly) operates ABS, TRAC, VSC, brake hold or brake assist, the ABS motor relay turns ON and drives the motor pump built into the brake actuator assembly. DTC No. Detection It

 Throttle / Pedal Position Sensor / Switch "A" Circuit Voltage Out of Range (P01201C)

DESCRIPTION Refer to DTC P012011. Click here DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note P01201C Throttle / Pedal Position Sensor / Switch "A" Circuit Voltage Out of Range The difference between the output voltage of VTA1 and VTA2 is less than

© 2016-2025 Copyright www.lexguide.net