Lexus ES: Remote Control System does not Operate
DESCRIPTION
The main body ECU (multiplex network body ECU) receives remote control signals from the driver door key cylinder or electrical key transmitter sub-assembly. Then, the main body ECU (multiplex network body ECU) activates the power window motor and sends the remote control signals to the sliding roof ECU (sliding roof drive gear sub-assembly) via LIN communication. The sliding roof ECU (sliding roof drive gear sub-assembly) receives those signals and activates the sliding roof motor.
CAUTION / NOTICE / HINT
NOTICE:
-
The sliding roof key-linked function and sliding roof wireless transmitter-linked function can be customized. Make sure that the customize settings of both functions are set to ON.
Click here
.gif)
-
If the sliding roof ECU (sliding roof drive gear sub-assembly) is removed and reinstalled or replaced, the sliding roof ECU (sliding roof drive gear sub-assembly) must be initialized.
Click here
-
The sliding roof system uses the CAN and LIN communication systems. First, confirm that there are no malfunctions in the CAN and LIN communication systems. Refer to How to Proceed with Troubleshooting.
Click here
-
If a sliding roof ECU (sliding roof drive gear sub-assembly) DTC is output, first perform troubleshooting for the sliding roof ECU (sliding roof drive gear sub-assembly) DTC.
Click here
-
Before replacing the main body ECU (multiplex network body ECU), refer to Registration.
Click here
PROCEDURE
| 1. | CHECK REMOTE CONTROL FUNCTION |
(a) Check the key-linked and wireless transmitter-linked functions.
Click here
| Result | Proceed to |
|---|---|
| Both the power windows and sliding roof operate by the key-linked and wireless transmitter-linked functions. | A |
| The sliding roof does not operate by the key-linked or wireless transmitter-linked function, but all of the power windows operate. | B |
| Both the power windows and sliding roof do not operate by the key-linked or wireless transmitter-linked function. | C |
| A | .gif) | USE SIMULATION METHOD TO CHECK |
| C | | GO TO POWER WINDOW CONTROL SYSTEM |
|
.gif)
| 2. | CHECK SLIDING ROOF OPERATION |
(a) Check the sliding roof operation.
Click here
OK:
Sliding roof operates normally.
| NG | | GO TO OTHER PROBLEM (Sliding Roof does not Move by Operating Sliding Roof Control Switch) |
|
| 3. | REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) |
(a) Replace the sliding roof ECU (sliding roof drive gear sub-assembly).
Click here
|
| 4. | INITIALIZE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) |
(a) Initialize the sliding roof ECU (sliding roof drive gear sub-assembly).
Click here
|
| 5. | CHECK REMOTE CONTROL FUNCTION |
(a) Check the key-linked and wireless transmitter-linked functions.
Click here
OK:
The key-linked and wireless transmitter-linked functions operate normally.
| OK | | END (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) WAS DEFECTIVE) |
| NG | | REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
READ NEXT:
Key-off Operation Function Operates even if Operating Conditions are not Satisfied
DESCRIPTION The sliding roof ECU (sliding roof drive gear sub-assembly) operates its built-in motor according to the sliding roof switch (map light sub-assembly) operation. Using the sliding roof swit
Sliding Roof does not Move by Operating Sliding Roof Control Switch
DESCRIPTION The sliding roof ECU (sliding roof drive gear sub-assembly) receives slide and tilt signals and operates its built-in motor when the sliding roof switch (map light sub-assembly) is operate
SEE MORE:
Right Rear Wheel Speed Sensor Signal Stuck Low (C051223)
DESCRIPTION Refer to DTC C051212 Click here DTC No. Detection Item DTC Detection Condition Trouble Area C051223 Right Rear Wheel Speed Sensor Signal Stuck Low
When the vehicle is driven from 0 km/h to 12 km/h (0 mph to 7 mph), the wheel speed is 1.8 km/h (1.1 mph) or less for 0
Installation
INSTALLATION PROCEDURE 1. INSTALL DCM (TELEMATICS TRANSCEIVER) 2. INSTALL NO. 1 TELEPHONE BRACKET (a) Install the No. 1 telephone bracket with the screw. 3. INSTALL TELEPHONE BRACKET (a) Install the telephone bracket with the screw. 4. INSTALL DCM (TELEMATICS TRANSCEIVER) WITH BRACKET (a) Connect ea
