Lexus ES: Operation Check
OPERATION CHECK
DCM OPERATION HISTORY
HINT:
- This function shows the telematics network status when the DCM (telematics transceiver) was operated. Use this when no DTC is present but this telematics system was unable to connect to the call center. This symptom may occur if cell phone signal strength is very weak.
- This function is used to display operation history information and the time at which it was stored in the DCM (telematics transceiver).
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Choose "Telematics" from the System Selection Menu, and then click "Utility".
(e) Click "DCM Operation History" on the Utility Selection Menu.
Body Electrical > Telematics > Utility| Tester Display |
|---|
| DCM Operation History |
(f) Choose "Items" on the DCM Operation History Menu.
HINT:
- When "Operation Code" is recorded, DCM Operation History is displayed on the Techstream.
- The displayed "Function" differs depending on the selected "Items".
(g) Refer to the following chart and check the system operation status displayed on the Techstream. (The following chart is an example of the system operation status.)
System Operation Status Example| Occurrence time (*1) | Operation Code (*2) | Function (*3) | Content (*4) | Roaming (*5) | Voice Call (*6) | Service Area (*7) | Electric Level (*8) |
|---|---|---|---|---|---|---|---|
| 2017/12/31 12:40:50 | 0101 | GNSS (Satellite) | Unreceived GNSS (Satellite) signal | ON | With | Out of Service | Level 0 |
| Tester Display | Description | Range | ||
|---|---|---|---|---|
| *1 | Occurrence time | Indicates date of the DCM (Telematics Transceiver) operation. | - | |
| *2 | Operation Code | Indicates the Operation Code. | - | |
| *3 | Function | Items | function name | - |
| Common |
| |||
| Remote Diagnostics |
| |||
| Center Request | Center Request Command | |||
| Remote Service |
| |||
| Remote Control |
| |||
| Security |
| |||
| Operation Monitor | Operation Monitoring | |||
| Network |
| |||
| Vehicle Information |
| |||
| *4 | Content | Indicates the content. | - | |
| *5 | Roaming | Indicates whether roaming was used for the communication network. | ON or OFF | |
| *6 | Voice Call | Indicates whether there was a voice call. | With or Without | |
| *7 | Service Area | Indicates whether the vehicle was in the service area. | Out of Service, Within Range, OFF the Air or Start up (LTE) | |
| *8 | Electric Level | Indicates the strength of the cellular signal received by the vehicle. | Level 0, Level 1, Level2, Level3, Level 4, Level 5 | |
READ NEXT:
Parts Location
PARTS LOCATION ILLUSTRATION *1 ROOF ANTENNA ASSEMBLY - GPS - Telephone Main *2 CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) *3 NAVIGATION ANTENNA ASSEMBLY - Telephone Sub *4 MAIN BOD
Precaution
PRECAUTION NOTICE: When disconnecting the cable from the negative (-) auxiliary battery terminal, initialize the following systems after the terminal is reconnected. System Name See Procedure
Problem Symptoms Table
PROBLEM SYMPTOMS TABLE HINT:
Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of
SEE MORE:
Terminals Of Ecu
TERMINALS OF ECU CHECK OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR) (a) Disconnect the J28 outer mirror control ECU assembly (driver door) connector. (b) Measure the voltage and resistance according to the value(s) in the table below. HINT: Measure the values on the wire harness side with the co
Problem Symptoms Table
PROBLEM SYMPTOMS TABLE NOTICE: Before replacing the main body ECU (multiplex network body ECU), refer to Registration. for Gasoline Model: Click here for HV Model: Click here HINT: Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the
