Lexus ES: Lubrication System
On-vehicle Inspection
ON-VEHICLE INSPECTION
PROCEDURE
1. CHECK ENGINE OIL LEVEL
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Put the engine in inspection Mode (Maintenance Mode).
Powertrain > Hybrid Control > Utility| Tester Display |
|---|
| Inspection Mode |
(e) Warm up and stop the engine, then wait for 5 minutes.
(f) Check that the engine oil level is between the low level and full level marks on the engine oil level dipstick.
If the level is low, check for engine oil leaks and add engine oil to the full level mark.
NOTICE:
Do not fill to above the full level mark.
HINT:
A certain amount of engine oil will be consumed while driving. In the following situations, engine oil consumption may increase, and engine oil may need to be refilled in between oil maintenance intervals.
- When the engine is new, for example directly after purchasing the vehicle or after replacing the engine.
- If low quality engine oil or oil of an inappropriate viscosity is used.
- When driving at high engine speeds or with a heavy load (when towing, etc.), or when accelerating or decelerating frequently while driving.
- When idling for a long time, or when driving frequently through heavy traffic.
When judging the amount of oil consumption, keep in mind that the oil may have become diluted, making it difficult to judge the true level accurately.
2. CHECK ENGINE OIL QUALITY
(a) Check the engine oil for deterioration, water intrusion, discoloration or thinning.
If the quality is visibly poor, replace the engine oil and oil filter sub-assembly.
3. INSPECT OIL PRESSURE
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Put the engine in Inspection mode (Maintenance Mode).
Powertrain > Hybrid Control > Utility| Tester Display |
|---|
| Inspection Mode |
(e) Enter the following menus: Powertrain / Engine / Data List / Engine Speed, Engine Oil Temperature Sensor and Engine Oil Pressure.
Powertrain > Engine > Data List| Tester Display |
|---|
| Engine Speed |
| Engine Oil Temperature Sensor |
| Engine Oil Pressure |
(f) Start the engine and warm it up until the engine oil temperature is 75 to 85°C (167 to 185°F).
(g) Read the Data List.
Standard| Engine Speed | Engine Oil Temperature Sensor | Engine Oil Pressure |
|---|---|---|
| 1500 rpm | 75 to 85°C (167 to 185°F) | 80 kPa(gauge) [12 psi(gauge)] or higher |
| 2500 rpm | 80 kPa(gauge) [12 psi(gauge)] or higher |
If the result is not as specified, check the quality of the engine oil and check the oil paths for clogging. Repair or replace if necessary. After performing replacement or repairs, if the engine oil pressure is not as specified, perform the confirmation driving pattern for DTC P052477, P15F009, P15F077, P15F109, P15F177 in SFI System and check for DTCs.
Click here .gif)
READ NEXT:
Oil And Oil Filter
ComponentsCOMPONENTS ILLUSTRATION *1 CENTER NO. 4 ENGINE UNDER COVER - - ILLUSTRATION *1 OIL FILTER SUB-ASSEMBLY *2 OIL FILLER CAP SUB-ASSEMBLY *3 GASKET *4 OIL PAN D
Components
COMPONENTS ILLUSTRATION *1 FRONT WHEEL OPENING EXTENSION PAD LH *2 FRONT WHEEL OPENING EXTENSION PAD RH *3 NO. 1 ENGINE UNDER COVER *4 NO. 2 ENGINE UNDER COVER ASSEMBLY N*m
SEE MORE:
Tilt and Telescopic ECU Communication Stop Mode
DESCRIPTION Detection Item Symptom Trouble Area Tilt and Telescopic ECU Communication Stop Mode Any of the following conditions are met:
Communication stop for "Multiplex Tilt and Telescopic" is indicated on the "Communication Bus Check" screen of the Techstream.
Click here
Com
Components
COMPONENTS ILLUSTRATION *1 REAR DIFFERENTIAL CARRIER ASSEMBLY *2 REAR NO. 1 DIFFERENTIAL SUPPORT *3 REAR NO. 2 DIFFERENTIAL SUPPORT - - Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) ● No
