Lexus ES: Lost Communication With ECM/PCM "A" Missing Message (U010087,U029387,U117087)
DESCRIPTION
The motor generator control ECU communicates with the hybrid vehicle control ECU, ECM and skid control ECU assembly via CAN communication.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| U010087 | Lost Communication With ECM/PCM "A" Missing Message | A CAN communication error between the ECM and motor generator control ECU (CAN communication system malfunction) occurs (1 trip detection logic) | CAN communication system | Comes on | Master Warning Light: Comes on |
| U029387 | Lost Communication With Hybrid Powertrain Control Module Missing Message | A CAN communication error between the hybrid vehicle control ECU and motor generator control ECU (CAN communication system malfunction) occurs (1 trip detection logic) | CAN communication system | Comes on | Master Warning Light: Comes on |
| U117087 | Lost Communication With Brake System Control Module(ch2) Missing Message | A CAN communication error between the skid control ECU assembly and motor generator control ECU (CAN communication system malfunction) occurs (1 trip detection logic) | CAN communication system | Comes on | Master Warning Light: Comes on |
MONITOR DESCRIPTION
If the motor generator control ECU detect problem with CAN communication with each ECU, it will illuminate the MIL and set a DTC.
MONITOR STRATEGY
| Related DTCs | U0100 (INF U010087): Lost Communication With ECM/PCM U0293 (INF U029387): Lost Communication With Hybrid Control Module U1170 (INF U117087): Lost Communication With Brake System Control Module |
| Required sensors/components | Motor generator control ECU |
| Frequency of operation | Continuous |
| Duration | TMC's intellectual property |
| MIL operation | Immediately |
| Sequence of operation | None |
TYPICAL ENABLING CONDITIONS
| The monitor will run whenever the following DTCs are not stored | TMC's intellectual property |
| Other conditions belong to TMC's intellectual property | - |
TYPICAL MALFUNCTION THRESHOLDS
| TMC's intellectual property | - |
COMPONENT OPERATING RANGE
| Motor generator control ECU | DTC U0100 (INF U010087) is not detected DTC U0293 (INF U029387) is not detected DTC U1170 (INF U117087) is not detected |
CONFIRMATION DRIVING PATTERN
HINT:
-
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here
.gif)
-
When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG) and turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the power switch off and wait for 2 minutes or more.
- Turn the power switch on (IG) and turn the Techstream on.
-
With power switch on (IG) and wait for 2 minutes or more. [*1]
HINT:
[*1]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- Enter the following menus: Powertrain / Motor Generator / Utility / All Readiness.
-
Check the DTC judgment result.
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE or N/A, perform the normal judgment procedure again.
PROCEDURE
| 1. | CHECK DTC OUTPUT (MOTOR GENERATOR CONTROL) |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Enter the following menus: Powertrain / Motor Generator / Trouble Codes.
(d) Check for DTCs.
Powertrain > Motor Generator > Trouble Codes| Result | Proceed to |
|---|---|
| None of the following DTCs are output. | A |
| Any of the following DTCs are also output. | B |
| DTC No. | Relevant DTC |
|---|---|
| P312487 | Lost Communication between Drive Motor "A" and HV ECU Missing Message |
HINT:
U010087, U029387 or U117087 may be stored due to a malfunction which also causes the DTCs in the preceding table to be stored. In this case, first troubleshoot the output DTCs in the preceding table. Then, perform a test to attempt to reproduce the problems, and check that no DTCs are output.
(e) Turn the power switch off.
| A | .gif) | GO TO CAN COMMUNICATION SYSTEM |
| B | | GO TO DTC CHART (MOTOR GENERATOR CONTROL SYSTEM) |
READ NEXT:
Precaution
PRECAUTION PRECAUTIONS FOR INSPECTING HYBRID CONTROL SYSTEM (a) Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insul
Definition Of Terms
DEFINITION OF TERMS Term Definition Monitor Description Description of what the motor generator control ECU monitors and how to detects malfunctions (monitoring purpose and its details).
SEE MORE:
Removal
REMOVAL CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during VVT sensor removal/installation are shown below. Necessary Procedures After Parts Removed/Installed/Repl
AUTO Power Retract Mirrors do not operate
DESCRIPTION The outer mirror switch assembly sends the retractable outer mirror switch signal to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) sends the auto retract/return signal to the outer mirror control ECU assemblies via CAN communication, which
