Lexus ES: Hybrid/EV Powertrain Control Module EEPROM Calibration / Parameter Memory Failure (P062F46)
DESCRIPTION
The hybrid vehicle control ECU monitors its internal operation and will store these DTCs when it detects an internal malfunction.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P062F46 | Hybrid/EV Powertrain Control Module EEPROM Calibration / Parameter Memory Failure | Either of the following conditions is met:
(1 trip detection logic) |
| Comes on | Master Warning Light: Comes on |
MONITOR DESCRIPTION
The hybrid vehicle control ECU monitors its internal operation. If the internal operation is malfunctioning, the hybrid vehicle control ECU illuminates the MIL and stores a DTC.
MONITOR STRATEGY
| Related DTCs | P062F (INF P062F46): Internal Control Module EEPROM Error |
| Required sensors/components | Hybrid vehicle control ECU |
| Frequency of operation | Continuous |
| Duration | TMC's intellectual property |
| MIL operation | Immediately |
| Sequence of operation | None |
TYPICAL ENABLING CONDITIONS
| The monitor will run whenever the following DTCs are not stored | TMC's intellectual property |
| Other conditions belong to TMC's intellectual property | - |
TYPICAL MALFUNCTION THRESHOLDS
| TMC's intellectual property | - |
COMPONENT OPERATING RANGE
| Hybrid vehicle control ECU | DTC P062F (INF P062F46) is not detected |
CONFIRMATION DRIVING PATTERN
HINT:
-
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here
.gif)
-
When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG) and turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the power switch off and wait for 2 minutes or more.
- Turn the power switch on (IG) and turn the Techstream on.
-
With power switch on (IG) and wait for 15 seconds or more. [*1]
HINT:
[*1]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
-
Check the DTC judgment result.
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE or N/A, perform the normal judgment procedure again.
PROCEDURE
| 1. | CHECK DATA (VEHICLE CONTROL HISTORY (HYBRID CONTROL)) |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Enter the following menus: Powertrain / Hybrid Control / Utility / Vehicle Control History (RoB).
Powertrain > Hybrid Control > Utility| Tester Display |
|---|
| Vehicle Control History (RoB) |
(d) Read and record the vehicle control history (Hybrid Control).
| Result | Proceed to |
|---|---|
| Auxiliary Battery Voltage Low (HV) or Auxiliary Battery Voltage Low (Inverter) is stored. | A |
| Auxiliary Battery Voltage Low (HV) and Auxiliary Battery Voltage Low (Inverter) are not stored. | B |
(e) Turn the power switch off.
| B | .gif) | REPLACE HYBRID VEHICLE CONTROL ECU |
|
.gif)
| 2. | CHECK DATA (FREEZE FRAME DATA (HYBRID CONTROL) AND VEHICLE CONTROL HISTORY (HYBRID CONTROL)) |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Read the Freeze Frame Data of DTC P062F46.
HINT:
The value of the Freeze Frame Data item BATT Voltage immediately after the power switch is turned on (IG) may be 16.00 V (15.99 V), however this does not indicate a malfunction.
(1) Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Powertrain > Hybrid Control > Trouble Codes(2) According to the display on the Techstream, read the data of the Freeze Frame Data and make a note of the value of Total Distance Traveled.
(d) Read the data recorded in the Vehicle Control History item (Auxiliary Battery Voltage Low (HV) or Auxiliary Battery Voltage Low (Inverter)) which was stored when the auxiliary battery voltage dropped below the threshold.
(1) Enter the following menus: Powertrain / Hybrid Control / Utility / Vehicle Control History (RoB).
Powertrain > Hybrid Control > Utility| Tester Display |
|---|
| Vehicle Control History (RoB) |
(2) According to the display on the Techstream, read the Vehicle Control History data and make a note of the value of Total Distance Traveled.
(e) Compare the values in the Freeze Frame Data and the Vehicle Control History.
| Result | Proceed to |
|---|---|
| The total distance driven is the same. | A |
| The total distance driven is not the same. | B |
(f) Turn the power switch off.
| B | | REPLACE HYBRID VEHICLE CONTROL ECU |
|
| 3. | CHECK AUXILIARY BATTERY VOLTAGE |
(a) Turn the power switch off and turn on the high beam headlights for 30 seconds. This will remove the surface charge from the auxiliary battery.
(b) Measure the auxiliary battery voltage according to the value(s) in the table below.
Standard Voltage:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Positive (+) auxiliary battery terminal - Negative (-) auxiliary battery terminal | 20°C (68°F), Power switch off | 12.0 V or higher |
HINT:
This DTC may be stored when the power switch is turned off when the auxiliary battery voltage is low. In this case, when the auxiliary battery voltage is no longer low, after the power switch is turned on (IG) and then off several times, the vehicle will be judged as normal and the master warning light will turn off.
| OK | | GO TO STEP 5 |
|
| 4. | RECHARGE OR REPLACE AUXILIARY BATTERY |
|
| 5. | CLEAR DTC |
Click here
|
| 6. | SIMULATION TEST |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG) and turn the Techstream on.
(c) With power switch on (IG) and wait for 15 seconds or more.
(d) Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
(e) Check if DTCs are output.
Powertrain > Hybrid Control > Trouble Codes| Result | Proceed to |
|---|---|
| P062F46 is not output. | A |
| P062F46 is output. | B |
(f) Turn the power switch off.
| A | | END |
| B | | REPLACE HYBRID VEHICLE CONTROL ECU |
READ NEXT:
ECM/PCM Power Relay Sense Circuit Intermittent (P06881F)
DESCRIPTION This DTC indicates that the hybrid vehicle control ECU detected an instantaneous interruption in +B power source voltage. DTC No. Detection Item DTC Detection Condition Trouble Ar
Transmission Range Sensor "A" Circuit (PRNDL Input) Signal Compare Failure (P070562)
DESCRIPTION The shift lever position sensor sends 7 different switch signals to the hybrid vehicle control ECU. The hybrid vehicle control ECU uses these signals to detect the shift lever position (P,
High Voltage System Interlock Circuit Open (P0A0A13,P0A0A92)
DTC SUMMARY MALFUNCTION DESCRIPTION The hybrid vehicle control ECU detects that a safety device (interlock) is operated or that there is an open circuit in the detection circuit. (Even if an open circ
SEE MORE:
Removal
REMOVAL CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during air fuel ratio sensor removal/installation are shown below. Necessary Procedures After Parts Removed/In
Open in Outer Mirror Indicator(Master) (C1AB4)
DESCRIPTION This DTC is stored when the blind spot monitor sensor RH detects an open in the outer rear view mirror indicator RH. DTC No. Detection Item DTC Detection Condition Trouble Area C1AB4 Open in Outer Mirror Indicator(Master) Both of the following conditions are met:
The
