Lexus ES manuals

Lexus ES: How To Proceed With Troubleshooting

CAUTION / NOTICE / HINT

HINT:

  • Use the following procedure to troubleshoot the audio and visual system.
  • *: Use the Techstream.

PROCEDURE

1.

VEHICLE BROUGHT TO WORKSHOP

NEXT

2.

CUSTOMER PROBLEM ANALYSIS

  • When troubleshooting, check that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
  • Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
  • The following 5 items are important points for problem analysis:

    What

    Vehicle model, system name

    When

    Date, time, occurrence frequency

    Where

    Road conditions

    Under what conditions?

    Driving conditions, weather conditions

    How did it happen?

    Problem symptoms

NEXT

3.

INSPECT BATTERY

(a) Measure the battery voltage.

Standard Voltage:

11 to 14 V

HINT:

If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.

NEXT

4.

CHECK CABIN

(a) Check that condensation is not likely to occur in the cabin and that the temperature is not high or extremely low in the cabin.

OK:

Condensation is not likely being produced and the temperature is not high or extremely low.

HINT:

  • A humid cabin and a rapid change in temperature may lead to condensation. Condensation in the cabin may cause a short circuit.
  • The audio and visual system may not operate normally when the temperature is -20°C (-4°F) or lower, or 65°C (149°F) or higher.
NG

SET CABIN TO APPROPRIATE TEMPERATURE

OK

5.

CHECK CAN COMMUNICATION SYSTEM*

(a) Check if CAN communication system DTCs are output.

Click here

Result

Proceed to

CAN DTCs are not output.

A

CAN DTCs are output.

B

B

GO TO CAN COMMUNICATION SYSTEM

A

6.

CHECK FOR DTC*

(a) Check for DTCs.

Body Electrical > Navigation System > Trouble Codes

Result

Proceed to

DTCs are output.

A

DTCs are not output.

B

B

GO TO STEP 10

A

7.

DTC CLEAR*

(a) Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs

HINT:

The present DTCs may not indicate actual malfunctions depending on the vehicle operating conditions.

NEXT

8.

RECHECK FOR DTC*

(a) Recheck for DTCs.

Body Electrical > Navigation System > Trouble Codes

Result

Proceed to

DTCs are output.

A

DTCs are not output.

B

HINT:

  • Even if the problem symptom is not confirmed, check for DTCs. This is because the system stores history DTCs.
  • If more information is needed, perform a recheck using the "System Check Mode" screen after rechecking for DTCs using the Techstream.
  • Check for DTCs and inspect the area that the code indicates.
B

GO TO STEP 10

A

9.

DIAGNOSTIC TROUBLE CODE CHART

(a) Find the output DTC in Diagnostic Trouble Code Chart.

Click here

NEXT

GO TO STEP 12

10.

PROBLEM SYMPTOMS TABLE

(a) Refer to Problem Symptoms Table.

Click here

Result

Proceed to

Fault is not listed in Problem Symptoms Table.

A

Fault is listed in Problem Symptoms Table.

B

HINT:

If the symptoms do not recur and no DTCs are output, attempt to reproduce the symptoms.

Click here

B

GO TO STEP 12

A

11.

PERFORM TROUBLESHOOTING BASED ON PROBLEM SYMPTOM

(a) Refer to Terminals of ECU.

Click here

NEXT

12.

CHECK CIRCUIT

(a) Adjust, repair or replace as necessary.

NEXT

13.

RECHECK FOR DTC*

(a) After clearing DTCs, recheck for DTCs.

Body Electrical > Navigation System > Clear DTCs Body Electrical > Navigation System > Trouble Codes
NEXT

14.

PERFORM CONFIRMATION TEST

NEXT

END

READ NEXT:

 Illumination for Panel Switch does not Come on with Tail Switch ON

CAUTION / NOTICE / HINT NOTICE: Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Pre

 Microphone Circuit

DESCRIPTION The radio receiver assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines. Using this circuit, the radio receive

 Mute Signal Circuit between Radio Receiver and Stereo Component Amplifier

DESCRIPTION This circuit sends a signal to the stereo component amplifier assembly to mute noise. Due to this, the noise produced by changing the sound source ceases. If there is an open in the circui

SEE MORE:

 DC/DC Converter Voltage Sensor "A"(VL) Circuit Intermittent (P314F1F)

DTC SUMMARY MALFUNCTION DESCRIPTION This DTC is stored if the value of "VL Voltage" fluctuates excessively. The cause of this malfunction may be one of the following: Area Main Malfunction Description Hybrid vehicle transaxle assembly Open or short circuit in the motor or generator coi

 Destination Information Undefined (C1AB8)

DESCRIPTION This DTC is stored when correct destination information is not sent from the main body ECU (multiplex network body ECU) and destination information cannot be confirmed after a blind spot monitor sensor has been replaced. Blind Spot Monitor Master DTC No. Detection Item DTC Detecti

© 2016-2024 Copyright www.lexguide.net