Lexus ES manuals

Lexus ES: Height Sensor Initialization Incomplete (B2450)

Lexus ES (XZ10) Service Manual / Vehicle Interior / Lighting (ext) / Lighting System (for Hv Model) / Height Sensor Initialization Incomplete (B2450)

DESCRIPTION

The headlight ECU sub-assembly LH stores this DTC if initialization has not been performed after it was replaced.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

DTC Output from

B2450

Height Sensor Initialization Incomplete

  • The power switch is on (IG).
  • Headlight ECU sub-assembly LH initialization not completed
  • -

Headlight ECU sub-assembly LH

AFS

CAUTION / NOTICE / HINT

NOTICE:

  • If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.

    Click here

  • When replacing the headlight ECU sub-assembly LH, always replace it with a new one. If a headlight ECU sub-assembly LH which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

PROCEDURE

1.

INITIALIZATION HEADLIGHT ECU SUB-ASSEMBLY LH

(a) Perform initialization of the headlight ECU sub-assembly LH.

Click here

NEXT

2.

CLEAR DTC

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / AFS / Trouble Codes.

(e) Clear the DTCs.

Body Electrical > AFS > Clear DTCs
NEXT

3.

CHECK FOR DTC

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / AFS / Trouble Codes.

(e) Check for DTCs.

Body Electrical > AFS > Trouble Codes

OK:

DTC B2450 is not output.

HINT:

If the headlight ECU sub-assembly LH stores DTC B2450 even though the ECU has been initialized, there may be a malfunction in the headlight ECU sub-assembly LH.

OK

END (INITIALIZATION WAS NOT COMPLETED)

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

READ NEXT:

 Variation Code not Written (B2451)

DESCRIPTION The headlight ECU sub-assembly LH stores this DTC if the vehicle specifications have not been stored. for LED Type Turn Signal Light DTC No. Detection Item DTC Detection Condition

 Abnormal Height Sensor Data at Initialization (B2452)

DESCRIPTION The headlight ECU sub-assembly LH stores this DTC if the value from the rear height control sensor sub-assembly LH is out of range when performing initialization of the headlight ECU sub-a

 Left Headlight ECU Variation Error (B2456)

DESCRIPTION This DTC is stored if the headlight ECU sub-assembly LH for another destination is installed. AFS*1 DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from

SEE MORE:

 Automatic High Beam Switch Indicator does not Come ON

DESCRIPTION When the automatic high beam system is on, the steering sensor illuminates the automatic high beam switch indicator. WIRING DIAGRAM PROCEDURE 1. READ VALUE USING TECHSTREAM (a) Connect the Techstream to the DLC3. (b) Turn the engine switch on (IG). (c) Turn the Techstream on. (

 Installation

INSTALLATION PROCEDURE 1. INSTALL STEERING GEAR HEAT INSULATOR (for 2GR-FKS) (a) Install the steering gear heat insulator to the rack and pinion power steering gear assembly with the 2 bolts in the order shown in the illustration. Torque: 8.0 N·m {82 kgf·cm, 71 in·lbf} 2. INSTALL

© 2016-2024 Copyright www.lexguide.net