Lexus ES: Front Right Microphone Circuit Component Internal Failure (B1AA696,B1AA71C)
DESCRIPTION
These DTCs are stored when a malfunction occurs in the No. 2 active noise control microphone system.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1AA696 | Front Right Microphone Circuit Component Internal Failure | Stereo component equalizer assembly detects malfunction in No. 2 active noise control microphone for 4 seconds or more continuously when engine speed is 1200 rpm or more* |
|
| B1AA71C | Front Right Microphone Circuit Circuit Voltage Out of Range | Stereo component equalizer assembly detects No. 2 active noise control microphone connection malfunction for 4 seconds or more continuously* |
|
HINT:
*: Malfunction monitoring is not performed under the following conditions, in order to prevent erroneous detection.
- After power switch is turned on (ACC) for 3 seconds or more.
- After the auxiliary battery voltage returns to normal for 3 seconds.
- Before 3 seconds have elapsed after auxiliary battery voltage has returned to normal.
WIRING DIAGRAM
PROCEDURE
| 1. | CLEAR DTC |
(a) Clear the DTCs.
Body Electrical > Active Noise Control > Clear DTCs
|
| 2. | CHECK FOR DTC |
(a) Check for DTCs with all of the detection conditions met.
Body Electrical > Active Noise Control > Trouble CodesOK:
No DTCs are output.
| OK |  | USE SIMULATION METHOD TO CHECK |
|
| 3. | CHECK HARNESS AND CONNECTOR (STEREO COMPONENT EQUALIZER ASSEMBLY - NO. 2 ACTIVE NOISE CONTROL MICROPHONE) |
(a) Disconnect the G15 stereo component equalizer assembly connector.
(b) Disconnect the P16 No. 2 active noise control microphone connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G15-6 (MC2+) - P16-1 (MC2+) | Always | Below 1 Ω |
| G15-20 (MC2-) - P16-2 (MC2-) | Always | Below 1 Ω |
| G15-6 (MC2+) or P16-1 (MC2+) - Body ground | Always | 10 kΩ or higher |
| G15-20 (MC2-) or P16-2 (MC2-) - Body ground | Always | 10 kΩ or higher |
| NG | | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
| 4. | REPLACE NO. 2 ACTIVE NOISE CONTROL MICROPHONE |
(a) Replace the No. 2 active noise control microphone with a new or known good one.
Click here .gif)
|
| 5. | CLEAR DTC |
(a) Clear the DTCs.
Body Electrical > Active Noise Control > Clear DTCs
|
| 6. | CHECK FOR DTC |
(a) Check for DTCs with all of the detection conditions met.
Body Electrical > Active Noise Control > Trouble CodesOK:
No DTCs are output.
| OK | | END (NO. 2 ACTIVE NOISE CONTROL MICROPHONE IS DEFECTIVE) |
| NG | | REPLACE STEREO COMPONENT EQUALIZER ASSEMBLY |
READ NEXT:
Rear Center Microphone Circuit Component Internal Failure (B1AAA96,B1AAB1C)
DESCRIPTION These DTCs are stored when a malfunction occurs in the No. 3 active noise control microphone system. DTC No. Detection Item DTC Detection Condition Trouble Area B1AAA96 Rear
Data List / Active Test
DATA LIST / ACTIVE TEST DATA LIST NOTICE: In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether
Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART Active Noise Control System DTC No. Detection Item Link B1AA044 ANC ECU EEPROM Data Memory Failure B1AA187 UART Communication Between ANC and Audi
SEE MORE:
System Description
SYSTEM DESCRIPTION GRILLE SHUTTER SYSTEM (a) General description The swing grille actuator assembly receives signals from the ECM, hybrid vehicle control ECU and air conditioning amplifier assembly via CAN communication. Based on these signals, the swing grille actuator assembly operates the radiato
Hybrid Battery Stack 2 Cell Voltage Detection Voltage Out of Range (P1A001C,P301A1C)
DESCRIPTION The HV battery is composed of 70 cells (3.7 V each) in series. The battery ECU assembly monitors the voltage of each HV battery cell to detect malfunctions of the HV battery. DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate P1A001C Hybri
