Lexus ES manuals

Lexus ES: Data List / Active Test

DATA LIST / ACTIVE TEST

DATA LIST

NOTICE:

In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Active Noise Control / Data List.

(e) Read the Data List according to the display on the Techstream.

Body Electrical > Active Noise Control > Data List

Tester Display

Measurement Item

Range

Reference Value

Diagnostic Note

Total Distance Traveled

Displays the current total driving distance

0 to 16777215

Equivalent to the actual total driving distance

Refer to the Total Distance Traveled - Unit for the units

Total Distance Traveled - Unit

Displays the current total driving distance units

km or mile

Units according destination

-

ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Active Noise Control / Active Test.

(e) Perform the Active Test according to the display on the Techstream.

Body Electrical > Active Noise Control > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Sound (All CH)

Test sound outputs in following order: Front No. 1 speaker assembly LH → Front No. 1 speaker assembly RH → Speaker assembly with bracket

ON or OFF

-

Sound "CH1"

Test sound output from front No. 1 speaker assembly LH

ON or OFF

-

Sound "CH2"

Test sound output from front No. 1 speaker assembly RH

ON or OFF

-

Sound "CH3"

Test sound output from speaker assembly with bracket

ON or OFF

-

Sound "CH4"

-

-

Cannot be used

READ NEXT:

 Diagnostic Trouble Code Chart

DIAGNOSTIC TROUBLE CODE CHART Active Noise Control System DTC No. Detection Item Link B1AA044 ANC ECU EEPROM Data Memory Failure B1AA187 UART Communication Between ANC and Audi

 Dtc Check / Clear

DTC CHECK / CLEAR CHECK FOR DTC (CHECK USING TECHSTREAM) (a) Connect the Techstream to the DLC3. (b) Turn the power switch on (IG). (c) Turn the Techstream on. (d) Enter the following menus: Body Elec

 Freeze Frame Data

FREEZE FRAME DATA CHECK FREEZE FRAME DATA HINT: Whenever an active noise control system DTC is stored, the stereo component equalizer assembly stores the current vehicle state as freeze frame data. (a

SEE MORE:

 Problem Symptoms Table

PROBLEM SYMPTOMS TABLE NOTICE: The following inspection procedures for the parking assist monitor system are based on the assumption that the audio and visual system*1 or navigation system*2 is normal. If the audio and visual system*1 or navigation system*2 has any malfunctions, first proceed wit

 Components

COMPONENTS ILLUSTRATION *1 BATTERY SERVICE HOLE COVER *2 SERVICE PLUG GRIP ILLUSTRATION *1 NO. 1 ENGINE COVER SUB-ASSEMBLY *2 INLET AIR CLEANER ASSEMBLY *3 AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE *4 COOL AIR INTAKE DUCT SEAL *5 NO. 1 ENGINE UNDER COVER -

© 2016-2025 Copyright www.lexguide.net