Lexus ES: Front Recognition Camera Optical Axis Misalignment Malfunction (C1AA800)
DESCRIPTION
The forward recognition camera monitors its optical axis status. If it determines that the optical axis alignment has become misaligned, it will store DTC C1AA800.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1AA800 | Front Recognition Camera Optical Axis Misalignment Malfunction | When the forward recognition camera detects an optical axis misalignment when the vehicle is being driven at a speed of 5 km/h (4 mph) or more, after 3 seconds have elapsed since the power switch was turned on (IG). |
|
CAUTION / NOTICE / HINT
NOTICE:
- When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.
-
If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera adjustment.
HINT:
Forward recognition camera adjustment can be performed by using either One Time Recognition or Sequential Recognition.
One Time Recognition: Click here
.gif)
Sequential Recognition: Click here
- When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Lexus genuine part. If a non-Lexus genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket or the forward recognition camera may not operate properly due to a difference in the transmissivity or black ceramic border.
- Forward recognition camera optical axis may deviate if the vehicle is driven on a banked road, such as a racetrack. This deviation can be corrected by driving the vehicle on a normal road for a while.
- Forward recognition camera optical axis may deviate when the vehicle is overloaded or the wheel alignment (toe-in) is incorrect. The forward recognition camera optical axis can be corrected by decreasing the load on the vehicle or adjusting the toe-in.
PROCEDURE
| 1. | CHECK FORWARD RECOGNITION CAMERA INSTALLATION |
(a) Check the installation condition of the forward recognition camera.
Click here
HINT:
If there is deformation or deviation in the forward recognition camera installation bracket, replace the windshield glass.
OK:
No deformation or deviation in forward recognition camera installation bracket.
| NG | .gif) | GO TO STEP 11 |
|
.gif)
| 2. | CHECK VEHICLE OPERATING CONDITION |
(a) Check the operating conditions of the vehicle.
HINT:
Check if a condition which caused the forward recognition camera optical axis to become temporarily misaligned existed, such as if the vehicle was overloaded, towed or modified.
OK:
Vehicle was not overloaded, towed or modified.
| NG | | GO TO STEP 9 |
|
| 3. | CHECK WHEEL ALIGNMENT |
(a) Check the front and rear wheel alignment (toe).
-
for front wheel alignment: Click here
-
for rear wheel alignment: Click here
| Result | Proceed to |
|---|---|
| Front and rear wheels are not misaligned (toe) | A |
| Front or rear wheel is misaligned (toe) | B |
| B | | GO TO STEP 6 |
|
| 4. | PERFORM FORWARD RECOGNITION CAMERA ADJUSTMENT |
(a) Perform forward recognition camera adjustment.
HINT:
Forward recognition camera adjustment can be performed by using either One Time Recognition or Sequential Recognition.
One Time Recognition: Click here
Sequential Recognition: Click here
|
| 5. | CLEAR DTC |
(a) Clear the DTCs.
Chassis > Front Recognition Camera > Clear DTCs| NEXT | | END |
| 6. | ADJUST WHEEL ALIGNMENT |
(a) Adjust the alignment (toe) of the wheels.
-
for front wheel alignment: Click here
-
for rear wheel alignment: Click here
|
| 7. | PERFORM FORWARD RECOGNITION CAMERA ADJUSTMENT |
(a) Perform forward recognition camera adjustment.
HINT:
Forward recognition camera adjustment can be performed by using either One Time Recognition or Sequential Recognition.
One Time Recognition: Click here
Sequential Recognition: Click here
|
| 8. | CLEAR DTC |
(a) Clear the DTCs.
Chassis > Front Recognition Camera > Clear DTCs| NEXT | | END |
| 9. | PERFORM FORWARD RECOGNITION CAMERA ADJUSTMENT |
(a) Return the vehicle to normal operating conditions.
(b) Perform forward recognition camera adjustment.
HINT:
Forward recognition camera adjustment can be performed by using either One Time Recognition or Sequential Recognition.
One Time Recognition: Click here
Sequential Recognition: Click here
|
| 10. | CLEAR DTC |
(a) Clear the DTCs.
Chassis > Front Recognition Camera > Clear DTCs| NEXT | | END |
| 11. | REPLACE WINDSHIELD GLASS |
(a) Replace the windshield glass.
Click here
|
| 12. | PERFORM FORWARD RECOGNITION CAMERA ADJUSTMENT |
(a) Perform forward recognition camera adjustment.
HINT:
Forward recognition camera adjustment can be performed by using either One Time Recognition or Sequential Recognition.
One Time Recognition: Click here
Sequential Recognition: Click here
|
| 13. | CLEAR DTC |
(a) Clear the DTCs.
Chassis > Front Recognition Camera > Clear DTCs| NEXT | | END |
READ NEXT:
Front Recognition Camera Heater Malfunction (C1AAE00)
DESCRIPTION The forward recognition camera controls the flow of current to the forward recognition with heater hood sub-assembly. If the forward recognition camera detects a malfunction in the forward
Lost Communication with Multi-axis Acceleration Sensor Module Missing Message (U012587,U012687,U012987,U014087,U029387)
DESCRIPTION When a malfunction is detected between various ECUs and sensors, these DTCs are stored. DTC No. Detection Item DTC Detection Condition Trouble Area U012587 Lost Communicatio
Internal Control Module Software Incompatibility Not Programmed (U030051)
DESCRIPTION The forward recognition camera receives vehicle information from the hybrid vehicle control ECU via CAN communication. DTC U030051 is stored when the vehicle information from the hybrid ve
SEE MORE:
Installation
INSTALLATION CAUTION / NOTICE / HINT NOTICE: Make sure to hold the front wiper arm while lifting it, as lifting the front wiper arm by the front wiper blade may damage or deform the front wiper blade. PROCEDURE 1. INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY (a) Using a T30 "TORX" socket wrench, install
Parts Location
PARTS LOCATION ILLUSTRATION *1 SPIRAL CABLE SUB-ASSEMBLY *2 STEERING WHEEL HEATER SWITCH (REFRESHING SEAT SWITCH) *3 INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ECU-IG1 NO. 3 FUSE *4 AIR CONDITIONING CONTROL ASSEMBLY *5 AIR CONDITIONING AMPLIFIER ASSEMBLY *6 RADIO RECEIV
