Lexus ES: EPS Warning Light Circuit
CAUTION / NOTICE / HINT
NOTICE:
- Perform this troubleshooting procedure when no DTCs are output, including DTCs related to CAN communication system malfunctions.
-
If the customer reports that the steering feels heavy, refer to the "Heavy steering" item in the Problem Symptoms Table.
Click here
.gif)
PROCEDURE
| 1. | CHECK ASSIST LIMIT RECORD |
(a) Using the Techstream, read the Data List item "Assist Limit Record 1".
Chassis > EMPS > Data List| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Assist Limit Record 1 | Information of assist limit that was used in the past or is currently in use (latest history) | Unrec, Mtr Overheat, Pow Vol Low, Pow Vol Low Prevent, Eng Stall, Ready OFF, Mtr Overload, Vhcl Spd Sig Malf, Batt Vol Keep | - | - |
| Tester Display |
|---|
| Assist Limit Record 1 |
HINT:
For the Data List item "Assist Limit Record 1", each item in the Range is described below.
| Range | Description |
|---|---|
| Mtr Overheat | When the vehicle is stopped or traveling at low speed, and steering operations are performed repeatedly or the steering wheel is turned all the way to the side and held there for a long time, assist may be limited in order to prevent overheating of the power steering motor assembly and power steering ECU assembly. After 10 minutes elapse with the engine stopped and no steering operations being performed, the system will return to normal. After recovering from the overheated condition, assist can be performed as usual. |
| Pow Vol Low | When insufficient battery charge, or battery degradation etc. causes the voltage to temporarily decrease, assist may be stopped. After the battery condition returns to normal, assist can be performed as usual. |
| Pow Vol Low Prevent | When insufficient battery charge, or battery degradation etc. causes the voltage to temporarily decrease, assist may be limited. After the battery condition returns to normal, assist can be performed as usual. |
| Eng Stall | When the engine stalls, battery charge becomes insufficient, so assist is stopped. After recovering from the engine stall, assist can be performed as usual. |
| Ready OFF | After Ready ON, if a malfunction in the HV system etc. causes a return to Ready OFF, the HV battery charge becomes insufficient, so assist is stopped. After returning to Ready ON state, assist can be performed as usual. |
| Mtr Overload | When the steering wheel cannot turn, such as when a road wheel is against a curb, if the driver continues to apply force to the steering wheel, current to the motor may be limited to prevent overheating. When the steering wheel is returned to a neutral position, assist can be performed as usual. |
| DC-DC Malf | If there is a malfunction in the DC-DC converter, etc., assist may be limited. After the DC-DC converter returns to normal, assist can be performed as usual. |
| Vhcl Spd Sig Malf | If the vehicle speed signal is abnormal due to a wheel speed sensor malfunction, etc., assist may be limited. |
| Batt Vol Keep | When insufficient battery charge, or battery degradation etc. causes the voltage to temporarily decrease, assist may be limited. After the battery condition returns to normal, assist can be performed as usual. |
(b) Based on the "Assist Limit Record 1" information, the following Data List items and the information from the customer interview, explain the situation to the customer.
Chassis > EMPS > Data List| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Record 1 Key Cycle | Number of times that the power switch was turned on (IG) before Assist Limit Record 1 was stored | Min.: 0 times Max.: 65535 times | - | - |
| Record 1 Key Cycle Elapsed Time | Period of time that elapsed since the power switch was turned on (IG) before Assist Limit Record 1 was stored | Min.: 0.0 s Max.: 53687091.1 s | - | - |
| Tester Display |
|---|
| Record 1 Key Cycle |
| Record 1 Key Cycle Elapsed Time |
| Result | Proceed to |
|---|---|
| "Unrec" is displayed | A |
| Other than Unrec is displayed | B |
HINT:
If it is necessary to investigate further into the past, check the "Assist Limit Record 2" and "Assist Limit Record 3" information in the same way as "Assist Limit Record 1".
| B | .gif) | EXPLAIN THE CHECKED "ASSIST LIMIT RECORD 1" TO THE CUSTOMER, CROSS-CHECKING THE DATA LIST ITEMS WITH THE INFORMATION FROM THE CUSTOMER INTERVIEW. |
|
.gif)
| 2. | INSPECT COMBINATION METER ASSEMBLY |
(a) Perform the Active Test of the combination meter assembly using the Techstream.
Click here
| Tester Display |
|---|
| EPS Warning |
(b) Check the combination meter assembly.
OK:
The EPS warning light turns on or off in accordance with the Techstream operation.
| OK | | REPLACE RACK AND PINION POWER STEERING GEAR ASSEMBLY |
| NG | | GO TO METER / GAUGE SYSTEM |
READ NEXT:
Check Assist Limit Record
CAUTION / NOTICE / HINT HINT: Perform this troubleshooting procedure when no DTCs are output, including DTCs related to CAN communication system malfunctions. PROCEDURE 1. READ VALUE USING TECHS
Precaution
PRECAUTION PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE BATTERY TERMINAL NOTICE: When disconnecting the cable from the negative (-) battery terminal, initialize the following system(s) after the c
SEE MORE:
Luggage Compartment Door Closer does not Operate
DESCRIPTION The luggage compartment door closer operation controls the luggage door closer assembly via the luggage closer motor assembly based on switch signals in the luggage door closer assembly. WIRING DIAGRAM CAUTION / NOTICE / HINT NOTICE:
Check that B2250 or B2251 is not output before pro
Transmission Range Sensor "A" Circuit Open (P070513,P070562)
DESCRIPTION The park/neutral position switch assembly detects the shift lever position and sends signals to the ECM. DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note P070513 Transmission Range Sensor "A" Circuit Open When the engine switch is on (IG)
