Lexus ES: Customize Parameters
CUSTOMIZE PARAMETERS
CUSTOMIZE PARKING SUPPORT BRAKE SYSTEM
(a) Customizing with the Techstream.
NOTICE:
- When the customer requests a change in a function, first make sure that the function can be customized.
- Be sure to make a note of the current settings before customizing.
- When troubleshooting a function, first make sure that the function is set to the default setting.
(1) Connect the Techstream to the DLC3.
(2) Turn the engine switch on (IG).
(3) Turn the Techstream on.
(4) Enter the following menus: Body Electrical / Advanced Parking Guidance/ICS/Intuitive P/A / Utility / Customize Setting.
(5) Select the setting by referring to the table below.
Warning| Tester Display | Description | Default | Setting | ECU |
|---|---|---|---|---|
| Fr Corner Sensor Onset Range | Sets the detection operation range for the front corner sensors. | Long | 0:Short,1:Long | Clearance warning ECU assembly |
| Rr Corner Sensor Onset Range | Sets the detection operation range for the rear corner sensors. | Long | 0:Short,1:Long | Clearance warning ECU assembly |
| Fr Sensor Onset Range | Sets the detection operation range for the front center sensors. | Wide | 0:Narrow,1:Wide | Clearance warning ECU assembly |
| Rr Sensor Onset Range | Sets the detection operation range for the rear center sensors. | Wide | 0:Narrow,1:Wide | Clearance warning ECU assembly |
| Intuitive P/A Auto Mute Function | Auto mute function. | ON | 0:ON,1:OFF | Clearance warning ECU assembly |
| Intuitive P/A Judgement of Obstacle on Course | Judgement of obstacle on course. | Valid | 0:Valid,1:Invalid | Clearance warning ECU assembly |
| Tester Display | Description | Default | Setting | ECU |
|---|---|---|---|---|
| Sensor Condition N | Makes the front sensors available when shift lever is in N. | Avail | 0:Not Avail,1:Avail | Clearance warning ECU assembly |
| Tester Display | Description | Default | Setting | ECU |
|---|---|---|---|---|
| Approach Display OFF | Sets whether the display turns off after an obstacle is no longer detected. | Avail | 0:Not Avail,1:Avail | Clearance warning ECU assembly |
| Display Mode | The display mode setting (when the intuitive parking assist system is normal). | All | 01:All,11:Undisp | Clearance warning ECU assembly |
| Tester Display | Description | Default | Setting | ECU |
|---|---|---|---|---|
| ICS Function | Parking support brake (static objects) function | ON | 0:ON,1:OFF | Clearance warning ECU assembly |
| ICS SW Status Memory | Parking support brake (static objects) function main switch memory function | Yes | 0:Yes,1:No | Clearance warning ECU assembly |
| ICS Stop Distance | Parking support brake (static objects) function target stopping distance | Long | 0:Short,1:Long | Clearance warning ECU assembly |
| RCTAB Function | Setting of the rear cross traffic auto brake function | ON | 0:ON,1:OFF | Clearance warning ECU assembly |
| RCTAB Operation Timing Setting | Setting of the activation timing of the rear cross traffic auto brake function | Standard | 0:Late,1:Standard | Clearance warning ECU assembly |
| RCTAB Sensitivity | Setting of the sensitivity of the rear cross traffic auto brake function | Standard | 0:Standard,1:Low | Clearance warning ECU assembly |
| Pedestrian ICS Function | Setting of the parking support brake (rear pedestrians) function | ON | 0:ON,1:OFF | Clearance warning ECU assembly |
| Pedestrian ICS Target Stopping Distance | Parking support brake (rear pedestrians) function target stopping distance | Normal | 0:Close,1:Normal | Clearance warning ECU assembly |
| Pedestrian ICS Width Adjustment (Y Axis) | Setting of the sensitivity of the parking support brake (rear pedestrians) function | Normal | 0:Narrow,1:Normal | Clearance warning ECU assembly |
READ NEXT:
Data List / Active Test
DATA LIST / ACTIVE TEST DATA LIST NOTICE: In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a pa
Diagnosis System
DIAGNOSIS SYSTEM DESCRIPTION (a) Parking support brake system data and Diagnostic Trouble Codes (DTCs) can be read from the Data Link Connector 3 (DLC3) of the vehicle. When the system seems to be mal
Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART Parking Support Brake System DTC No. Detection Item Link C1625 Open or Short in Steering Angle Sensor +B C1626 Steering Angle Sensor Failure
SEE MORE:
Removal
REMOVAL CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during brake pedal support assembly removal/installation are shown below. Necessary Procedures After Parts Remove
Components
COMPONENTS ILLUSTRATION *1 FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY - - Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) N*m (kgf*cm, ft.*lbf): Specified torque *T1 Bolt color black: 8.0
