Lexus ES manuals

Lexus ES: Cruise Main Indicator Light Circuit

DESCRIPTION

When the dynamic radar cruise control system is turned on using the cruise control main switch, the cruise control indicator (vehicle-to-vehicle distance control mode) illuminates. The ECM uses this and other indicators to indicate the status (presence or absence of a preceding vehicle, vehicle-to-vehicle distance, malfunction of system or related systems) of the dynamic radar cruise control system.

CAUTION / NOTICE / HINT

NOTICE:

  • Before replacing the ECM, refer to Registration.

    Click here

  • When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

PROCEDURE

1.

PERFORM ACTIVE TEST USING TECHSTREAM

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Combination Meter / Active Test.

(e) Perform the Active Test according to the display on the Techstream.

Body Electrical > Combination Meter > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Multi Display All (White)

Multi-information display (White display)

ON

-

Body Electrical > Combination Meter > Active Test

Tester Display

Multi Display All (White)

Result

Proceed to

The multi-information display in the combination meter assembly turns on according to the operation of the Active Test.

A

The multi-information display in the combination meter assembly does not turn on according to the operation of the Active Test.

B

B

GO TO METER / GAUGE SYSTEM

A

2.

READ VALUE USING TECHSTREAM

(a) Enter the following menus: Powertrain / Radar Cruise 1 / Data List.

(b) Read the Data List according to the display on the Techstream.

Powertrain > Radar Cruise1 > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Cruise Indicator

Cruise control indicator status

ON or OFF

ON: Cruise control indicator illuminates

OFF: Cruise control indicator turns off

-

Powertrain > Radar Cruise1 > Data List

Tester Display

Cruise Indicator

Result

Proceed to

The cruise control indicator illuminates and turns off according to the operation of the cruise control main switch.

A

The cruise control indicator does not illuminate but the Data List items change according to the operation of the cruise control main switch.

B

The cruise control indicator does not illuminate and the Data List items do not change according to the operation of the cruise control main switch.

C

A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

REPLACE COMBINATION METER ASSEMBLY

C

REPLACE ECM

READ NEXT:

 Cruise Main Indicator Light Circuit

DESCRIPTION When the dynamic radar cruise control system is turned on using the cruise control main switch, the cruise control indicator (vehicle-to-vehicle distance control mode) illuminates. The ECM

 Cruise SET Indicator Light Circuit

DESCRIPTION The ECM illuminates the cruise SET indicator by sending request signals to the combination meter assembly via CAN communication. The cruise SET indicator illuminates when the dynamic radar

 Cruise SET Indicator Light Circuit

DESCRIPTION The ECM illuminates the cruise SET indicator by sending request signals to the combination meter assembly via CAN communication. The cruise SET indicator illuminates when the dynamic radar

SEE MORE:

 Engine Oil Pressure Sensor/Switch "A" Signal Stuck High (P052024,P05202A)

DESCRIPTION Refer to DTC P052012. Click here DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note P052024 Engine Oil Pressure Sensor/Switch "A" Signal Stuck High The oil pressure sensor output voltage is higher than the threshold value (1 trip detectio

 Front Recognition Camera Heater Malfunction (C1AAE00)

DESCRIPTION The forward recognition camera controls the flow of current to the forward recognition with heater hood sub-assembly. If the forward recognition camera detects a malfunction in the forward recognition with heater hood sub-assembly circuit, it will store this DTC. DTC No. Detection I

© 2016-2024 Copyright www.lexguide.net