Lexus ES: Cellular Phone Inspection
PROCEDURE
| 1. | CHECK USAGE CONDITION |
(a) Check that the vehicle and cellular phone meet the following conditions:
NOTICE:
If changing cellular phone settings, updating software, etc. is necessary, make sure to obtain the permission of the customer before performing it.
-
The cellular phone is "Bluetooth" compatible.
Click here
.gif)
- The cellular phone is registered as a hands-free device.
- "Bluetooth" setting of the cellular phone is on.
- Operating system and software of the cellular phone are the latest versions.
- There are no other radio wave emitting devices ("Wi-Fi" communication device, etc.) in the cabin.
- The "Wi-Fi" setting of the cellular phone is off.
- The "Wi-Fi" tethering setting of the cellular phone is off.
(b) Connect the cellular phone to the in-vehicle device and check that it is connected correctly.
| Result | Proceed to |
|---|---|
| The cellular phone is connected correctly. | A |
| The cellular phone is not connected correctly. | B |
| A | .gif) | END |
|
.gif)
| 2. | RESTART CELLULAR PHONE |
(a) Restart the cellular phone.
(b) Turn the power switch off.
(c) Turn the power switch on (ACC).
(d) Connect the cellular phone to the in-vehicle device and check that it is connected correctly.
| Result | Proceed to |
|---|---|
| The cellular phone is connected correctly. | A |
| The cellular phone is not connected correctly. | B |
| A | | END |
|
| 3. | CHECK OPERATION |
(a) Check if the in-vehicle device can be recognized by the cellular phone.
| Result | Proceed to |
|---|---|
| In-vehicle device can be recognized. | A |
| In-vehicle device cannot be recognized. | B |
| B | | GO TO STEP 5 |
|
| 4. | REGISTER AGAIN |
(a) Clear all "Bluetooth" devices registered to the cellular phone and the radio receiver assembly.
(b) Register the cellular phone again.
(c) Connect the cellular phone to the in-vehicle device and check that it is connected correctly.
| Result | Proceed to |
|---|---|
| The cellular phone is connected correctly. | A |
| The cellular phone is not connected correctly. | B |
| A | | END |
|
| 5. | CHECK USING ANOTHER VEHICLE |
(a) Check if the customer's cellular phone functions normally using another "Bluetooth" compatible vehicle.
HINT:
- Make sure to obtain the customer's permission to perform this procedure.
- After the inspection, clear the registered information and usage history acquired during the inspection.
| Result | Proceed to |
|---|---|
| The cellular phone is connected correctly. | A |
| The cellular phone is not connected correctly. | B |
| A | | PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
|
| 6. | CHECK USING ANOTHER CELLULAR PHONE |
(a) Check if the system functions normally using another "Bluetooth" compatible cellular phone.
HINT:
- Make sure to obtain the customer's permission to perform this procedure.
- After the inspection, clear the registered information and usage history acquired during the inspection.
| Result | Proceed to |
|---|---|
| The cellular phone is connected correctly. | A |
| The cellular phone is not connected correctly. | B |
| A | | END (ONLY A "Bluetooth" COMPATIBLE CELLULAR PHONE CAN BE USED) |
| B | | PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
READ NEXT:
Cellular Phone Registration Failure
CAUTION / NOTICE / HINT NOTICE:
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Pre
Cursor or Map Rotates when Vehicle Stopped
PROCEDURE 1. CHECK CONDITION (a) Check with the customer if the vehicle has been turned by a turntable. OK: Vehicle has not been turned by a turntable. HINT: If the vehicle is turned on a
Customize Parameters
CUSTOMIZE PARAMETERS CUSTOMIZING WITH REMOTE TOUCH (REMOTE OPERATION CONTROLLER ASSEMBLY) (a) Customizing with the touch function cancellation function. (w/ Touch Function Cancellation Function) NOTIC
SEE MORE:
Short to GND in Outer Mirror Indicator(Master) (C1AB2)
DESCRIPTION This DTC is stored when the blind spot monitor sensor RH detects a short to ground in the outer rear view mirror indicator RH. DTC No. Detection Item DTC Detection Condition Trouble Area C1AB2 Short to GND in Outer Mirror Indicator(Master) Both of the following conditio
Installation
INSTALLATION CAUTION / NOTICE / HINT HINT:
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
PROCEDURE 1. INSTALL HEADLIGHT ASSEMBLY (a) Connect the connector and raise the connector lock lever to engage the claw and lock the connector as shown i
