Lexus ES manuals

Lexus ES: Cancellation of 4WD Control (C1299)

DESCRIPTION

This DTC is output if the heat generated by the transmission coupling assembly exceeds a certain amount or if the estimated oil temperature of the transfer exceeds a certain amount while driving.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

C1299

Cancellation of 4WD Control

The heat generated by the differential coupling exceeds a certain amount.

  • Condition, size or tire pressure of the front or rear tires
  • Suspension and ball joint
  • Drive shaft
  • Propeller shaft
  • Transmission coupling assembly
  • 4WD ECU assembly

PROCEDURE

1.

CHECK VEHICLE USAGE

(a) Check that there has been no unintended vehicle usage.

OK:

There is no evidence of rough use (the vehicle has not been driven on damaged or snowy roads, etc. for a long time).

NG

CHECK FOR INTERMITTENT PROBLEMS

OK

2.

CHECK FOR DTC

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Turn the Techstream on.

(d) Check if the electronically controlled brake system DTC is output.

Chassis > Brake/EPB > Trouble Codes

(e) Read the DTCs using the Techstream.

Result

Proceed to

Only DTC C1299 is output

A

DTC C1299 and other DTCs (electronically controlled brake system DTC) are output

B

B

REPAIR CIRCUIT INDICATED BY OUTPUT CODE (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)

A

3.

CHECK RELATED PART

(a) Check the condition, size and tire pressure of the front and rear tires.

Click here

(b) Inspect the suspension and ball joint, etc. for rattle.

(c) Inspect the drive shaft and propeller shaft rotation condition.

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS

OK

4.

RECONFIRM DTC

(a) Clear the DTC.

Chassis > Four Wheel Drive > Clear DTCs

(b) Start the engine.

(c) Drive the vehicle at a speed of 20 km/h (12 mph) or more and check that the same DTC is output.

Chassis > Four Wheel Drive > Trouble Codes

Result

Proceed to

DTC is output

A

DTC is not output

B

B

CHECK FOR INTERMITTENT PROBLEMS

A

5.

REPLACE 4WD ECU ASSEMBLY

(a) Replace the 4WD ECU assembly.

Click here

NEXT

6.

RECONFIRM DTC

(a) Clear the DTC.

Chassis > Four Wheel Drive > Clear DTCs

(b) Start the engine.

(c) Drive the vehicle at a speed of 20 km/h (12 mph) or more and check that the same DTC is output.

Chassis > Four Wheel Drive > Trouble Codes

Result

Proceed to

DTC is output

A

DTC is not output

B

A

REPLACE TRANSMISSION COUPLING ASSEMBLY

B

END

READ NEXT:

 Diameter of the Tire is not Uniform (C1337)

DESCRIPTION The 4WD ECU assembly outputs this DTC if a difference in tire size is detected. DTC No. Detection Item DTC Detection Condition Trouble Area C1337 Diameter of the Tire is not

 Calibration

CALIBRATION NOTICE: Initial AWD functions such as acceleration are sometimes affected unless backup memory is cleared. When the yaw rate and acceleration sensor (airbag ECU assembly) is replaced,

 Data List / Active Test

DATA LIST / ACTIVE TEST NOTICE: In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faul

SEE MORE:

 Inspection

INSPECTION PROCEDURE 1. INSPECT BRAKE CYLINDER AND PISTON (a) Check the front disc brake cylinder bore and front disc brake piston for rust and scoring. If necessary, replace the front disc brake cylinder assembly and front disc brake piston. 2. INSPECT PAD LINING THICKNESS (a) Using a ruler, mea

 Diagnostic Trouble Code Chart

DIAGNOSTIC TROUBLE CODE CHART LIN Communication System DTC No. Detection Item Link B1206 P/W Master Switch Communication Stop B1273 Sliding Roof ECU Communication Stop B2321 D-Door Motor ECU Communication Stop B2322 P-Door Motor ECU Communication Stop

© 2016-2024 Copyright www.lexguide.net