Lexus ES manuals

Lexus ES: Stereo Jack Adapter Light does not Illuminate

Lexus ES (XZ10) Service Manual / Audio & Visual & Telematics / Audio / Video / Audio And Visual System (for Gasoline Model) / Stereo Jack Adapter Light does not Illuminate

DESCRIPTION

Power is supplied to the No. 1 stereo jack adapter assembly illumination from the radio receiver assembly.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

    Click here

  • When replacing the radio receiver assembly, always replace it with a new one. If a radio receiver assembly which was installed to another vehicle is used, the following may occur:
    • A communication malfunction DTC may be stored.
    • The radio receiver assembly may not operate normally.

PROCEDURE

1.

CHECK HARNESS AND CONNECTOR (NO. 1 STEREO JACK ADAPTER ASSEMBLY ILLUMINATION POWER SOURCE)

(a) Disconnect the G103 and G8 No. 1 stereo jack adapter assembly connectors.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

G103-1 (UPI) - Body ground

Engine switch on (ACC)

5 V

G8-8 (ACC) - Body ground

Engine switch on (ACC)

11 to 14 V

*a

Front view of wire harness connector

(to No. 1 Stereo Jack Adapter Assembly)
OK

REPLACE NO. 1 STEREO JACK ADAPTER ASSEMBLY

NG

2.

CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)

(a) Disconnect the G112 radio receiver assembly connector.

(b) Disconnect the G103 No. 1 stereo jack adapter assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

G103-1 (UPI) - G112-1 (USV1)

Always

Below 1 Ω

G103-1 (UPI) or G112-1 (USV1) - Body ground

Always

10 kΩ or higher

*a

Front view of wire harness connector

(to Radio Receiver Assembly)

*b

Front view of wire harness connector

(to No. 1 Stereo Jack Adapter Assembly)
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

3.

CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)

(a) Disconnect the G6 radio receiver assembly connector.

(b) Disconnect the G8 No. 1 stereo jack adapter assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

G8-8 (ACC) - G6-16 (ACC)

Always

Below 1 Ω

G8-8 (ACC) or G6-16 (ACC) - Body ground

Always

10 kΩ or higher
OK

REPLACE RADIO RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

READ NEXT:

 Switch Lights of Remote Touch Always Illuminate or cannot be Controlled Using Rheostat

DESCRIPTION Power is supplied to the remote touch (remote operation controller assembly) illumination when the light control switch is in the tail or head position. HINT: When the remote touch (rem

 Switch Lights of Remote Touch do not Illuminate

DESCRIPTION Power is supplied to the remote touch (remote operation controller assembly) illumination when the light control switch is in the tail or head position. WIRING DIAGRAM CAUTION / NOTICE /

 Switch Operation of Remote Touch not Accepted

CAUTION / NOTICE / HINT NOTICE: Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Pre

SEE MORE:

 Installation

INSTALLATION PROCEDURE 1. INSTALL HOOD LOCK CONTROL CABLE ASSEMBLY (a) Pass the hood lock control cable assembly into the engine compartment. (b) Engage the grommet. (c) Engage each clamp. (d) Engage the clamp to install the hood lock control cable assembly. 2. INSTALL HOOD LOCK CONTROL LEVER SUB-AS

 Dtc Check / Clear

DTC CHECK / CLEAR NOTICE: When the diagnosis system is changed from normal mode to check mode or vice versa, all DTCs and Freeze Frame Data recorded in normal mode are cleared. Before changing modes, always check and make a note of DTCs and Freeze Frame Data. HINT: DTCs which are stored in the EC

© 2016-2025 Copyright www.lexguide.net