Lexus ES: Side Camera Feedback Malfunction (C1683)
DESCRIPTION
This DTC is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the passenger side television camera assembly to the parking assist ECU.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1683 | Side Camera Feedback Malfunction | Side camera feedback malfunction |
|
WIRING DIAGRAM
.png)
CAUTION / NOTICE / HINT
NOTICE:
-
When "!" is displayed on the multi-display assembly after the cable is disconnected from the negative (-) auxiliary battery terminal, correct the steering angle neutral point.
Click here
.gif)
-
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.
Click here
PROCEDURE
| 1. | CHECK FOR DTC |
(a) Clear the DTCs.
Chassis > Circumference Monitoring Camera Control Module > Clear DTCs(b) Check for DTCs.
Chassis > Circumference Monitoring Camera Control Module > Trouble CodesOK:
DTC C1683 is not output.
| OK | .gif) | USE SIMULATION METHOD TO CHECK |
|
.gif)
| 2. | CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY RH) |
(a) Disconnect the N43 parking assist ECU connector.
(b) Disconnect the J12 outer rear view mirror assembly RH connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N43-40 (RCB+) - J12-2 (RCB+) | Always | Below 1 Ω |
| N43-38 (RCV+) - J12-7 (RCV+) | Always | Below 1 Ω |
| N43-16 (RCV-) - J12-6 (RCV-) | Always | Below 1 Ω |
| N43-17 (RGND) - J12-1 (RGND) | Always | Below 1 Ω |
| N43-39 (SGND) - J12-3 (SGND) | Always | Below 1 Ω |
| N43-40 (RCB+) or J12-2 (RCB+) - Body ground | Always | 10 kΩ or higher |
| N43-38 (RCV+) or J12-7 (RCV+) - Body ground | Always | 10 kΩ or higher |
| N43-16 (RCV-) or J12-6 (RCV-) - Body ground | Always | 10 kΩ or higher |
| N43-17 (RGND) or J12-1 (RGND) - Body ground | Always | 10 kΩ or higher |
| N43-39 (SGND) or J12-3 (SGND) - Body ground | Always | 10 kΩ or higher |
| NG | | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
| 3. | CHECK PARKING ASSIST ECU (RCV-, RGND) |
(a) Disconnect the N43 parking assist ECU connector.
| (b) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
| NG | | REPLACE PARKING ASSIST ECU |
|
| 4. | CHECK PARKING ASSIST ECU (RCB+, RGND) |
| (a) Remove the parking assist ECU with the connector still connected. |
|
.png)
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N43-17 (RGND) - Body ground | Always | Below 1 Ω |
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N43-40 (RCB+) - N43-17 (RGND) | Power switch on (IG) | 5.5 to 7.05 V |
| NG | | REPLACE PARKING ASSIST ECU |
|
| 5. | CHECK SIDE TELEVISION CAMERA ASSEMBLY RH (RCV+, RGND) |
(a) Remove the parking assist ECU with the connector still connected.
(b) Using an oscilloscope, check the waveform of the side television camera assembly RH.
HINT:
A waterproof connector is used for the side television camera assembly RH. Therefore, inspect the waveform at the parking assist ECU with the connector connected.
| *a | Component with harness connected (Parking Assist ECU) | *b | Waveform 1 (camera lens not covered, displaying an image) |
| *c | Waveform 2 (camera lens covered, blacking out the screen) | *d | Synchronization Signal |
| *e | Video Waveform | - | - |
HINT:
- The video waveform changes according to the image sent by the side television camera assembly RH.
- The video waveform is constantly output when the power switch is on (ACC).
| Item | Content |
|---|---|
| Tester Connection | N43-38 (RCV+) - N43-17 (RGND) |
| Tool Setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | Power switch on (IG), panoramic view monitor system operating |
OK:
Waveform is similar to that shown in illustration.
| OK | | REPLACE PARKING ASSIST ECU |
|
| 6. | REPLACE SIDE TELEVISION CAMERA ASSEMBLY RH |
(a) Replace the side television camera assembly RH with a new or normally functioning one.
Click here
|
| 7. | CHECK FOR DTC |
(a) Clear the DTCs.
Chassis > Circumference Monitoring Camera Control Module > Clear DTCs(b) Check for DTCs.
Chassis > Circumference Monitoring Camera Control Module > Trouble CodesOK:
DTC C1683 is not output.
| OK | | END (SIDE TELEVISION CAMERA ASSEMBLY RH IS DEFECTIVE) |
| NG | | REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH |
READ NEXT:
Side Camera Current Malfunction (C1684)
DESCRIPTION This DTC is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the passenger side television ca
Driver Side Camera Video Sync Signal Malfunction (C1686)
DESCRIPTION This DTC is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the driver side television camer
Over Current Detected in Driver Side Camera (C1687)
DESCRIPTION This DTC is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the driver side television camer
SEE MORE:
DC/DC Converter Current Sensor Circuit Short to Ground (P0E5111,P0E5115,P0E511F)
DESCRIPTION DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate P0E5111 DC/DC Converter Current Sensor Circuit Short to Ground Short to GND detected in reactor current sensor circuit (1 trip detection logic) Inverter with converter assembly Comes
Steering Angle Sensor Module Calibration / Parameter Memory Failure (C052646)
DESCRIPTION When the vehicle is being driven in a straight line at 15 km/h (9 mph) for 1 second or more, the skid control ECU (brake actuator assembly) calculates the steering angle sensor zero point and updates the zero point if the difference between the calculated zero point and current zero poin
