Lexus ES manuals

Lexus ES: Right Headlight ECU Malfunction (B242C,B242D)

Lexus ES (XZ10) Service Manual / Vehicle Interior / Lighting (ext) / Lighting System (for Gasoline Model) / Right Headlight ECU Malfunction (B242C,B242D)

DESCRIPTION

The headlight ECU sub-assembly LH or headlight ECU sub-assembly RH stores a DTC if it detects an internal malfunction.

for LED Type Turn Signal Light

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

DTC Output from

B242C

Right Headlight ECU Malfunction
  • The engine switch is on (IG).
  • Headlight ECU sub-assembly RH internal malfunction
  • Maximum 15 minutes

Headlight ECU sub-assembly RH

AFS (Sub)

B242D

Left Headlight ECU Malfunction
  • The engine switch is on (IG).
  • Headlight ECU sub-assembly LH internal malfunction
  • Maximum 15 minutes

Headlight ECU sub-assembly LH

AFS
for Bulb Type Turn Signal Light

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

DTC Output from

B242C

Right Headlight ECU Malfunction
  • The engine switch is on (IG).
  • Headlight ECU sub-assembly RH internal malfunction
  • Maximum 15 minutes

Headlight ECU sub-assembly RH

HL AutoLeveling (Sub)

B242D

Left Headlight ECU Malfunction
  • The engine switch is on (IG).
  • Headlight ECU sub-assembly LH internal malfunction
  • Maximum 15 minutes

Headlight ECU sub-assembly LH

HL AutoLeveling

CAUTION / NOTICE / HINT

NOTICE:

  • If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.*1

    Click here

  • If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information the headlight ECU sub-assembly LH.*2

    Click here

  • When replacing the headlight ECU sub-assembly LH, always replace it with a new one. If a headlight ECU sub-assembly LH which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
    • *1: for LED Type Turn Signal Light
    • *2: for Bulb Type Turn Signal Light

PROCEDURE

1.

CONFIRM MODEL

(a) Choose the model to be inspected.

Result

Proceed to

for LED Type Turn Signal Light

A

for Bulb Type Turn Signal Light

B
B

GO TO STEP 4

A

2.

CLEAR DTC

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / AFS or AFS (Sub) / Trouble Codes.

(e) Clear the DTCs.

Body Electrical > AFS > Clear DTCs Body Electrical > AFS (Sub) > Clear DTCs
NEXT

3.

CHECK FOR DTC

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Wait for at least maximum 15 minutes.

(d) Turn the Techstream on.

(e) Enter the following menus: Body Electrical / AFS or AFS (Sub) / Trouble Codes.

(f) Check for DTCs.

Body Electrical > AFS > Trouble Codes Body Electrical > AFS (Sub) > Trouble Codes

OK:

DTC B242C and B242D are not output.

Result

Proceed to

OK

A

NG (DTC B242C is output)

B

NG (DTC B242D is output)

C
A

USE SIMULATION METHOD TO CHECK

B

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

C

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

4.

CLEAR DTC

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / HL AutoLeveling or HL AutoLeveling (Sub) / Trouble Codes.

(e) Clear the DTCs.

Body Electrical > HL AutoLeveling > Clear DTCs Body Electrical > HL AutoLeveling (Sub) > Clear DTCs
NEXT

5.

CHECK FOR DTC

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Wait for at least maximum 15 minutes.

(d) Turn the Techstream on.

(e) Enter the following menus: Body Electrical / HL AutoLeveling or HL AutoLeveling (Sub) / Trouble Codes.

(f) Check for DTCs.

Body Electrical > HL AutoLeveling > Trouble Codes Body Electrical > HL AutoLeveling (Sub) > Trouble Codes

OK:

DTC B242C and B242D are not output.

Result

Proceed to

OK

A

NG (DTC B242C is output)

B

NG (DTC B242D is output)

C
A

USE SIMULATION METHOD TO CHECK

B

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

C

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

READ NEXT:

 Open in IG Circuit (B242E)

DESCRIPTION The headlight ECU sub-assembly operates using the power source voltage input from the IG terminal and ECUB terminal. The IG terminal power source voltage is supplied by turning the IG1-NO.

 Open in B Power Line (B242F)

DESCRIPTION The headlight ECU sub-assembly operates using the power source voltage input from the IG terminal and ECUB terminal. The power source voltage of the ECUB terminal is supplied when the main

 Headlight LH Circuit (B2439,B243A)

DESCRIPTION The headlight ECU sub-assembly LH and headlight ECU sub-assembly RH internally boost the power supply voltage to ensure a constant supplied current for the lo/hi beam LED of their respecti

SEE MORE:

 Ignition Coil "A" Circuit Open (P035113-P035613)

DESCRIPTION HINT: These DTCs indicate malfunctions relating to the primary circuit. If DTC P035113 is output, check the No. 1 ignition coil assembly circuit. If DTC P035213 is output, check the No. 2 ignition coil assembly circuit. If DTC P035313 is output, check the No. 3 ignition coil ass

 Removal

REMOVAL CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during exhaust manifold assembly RH (TWC: Front Catalyst) and exhaust manifold assembly LH (TWC: Front Catalyst

© 2016-2024 Copyright www.lexguide.net