Lexus ES: Lost Communication with Image Processing Sensor B (U0266-U0268)
DESCRIPTION
These DTCs are stored when communication between the parking assist ECU and front television camera assembly, side television camera assembly LH, side television camera RH is not possible.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| U0266 | Lost Communication with Image Processing Sensor B | Lost Communication with side television camera assembly LH | CAN communication system |
| U0267 | Lost Communication with Image Processing Sensor C | Lost Communication with front television camera assembly | CAN communication system |
| U0268 | Lost Communication with Image Processing Sensor D | Lost Communication with side television camera assembly RH | CAN communication system |
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
-
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here
.gif)
- Inspect the fuses for circuits related to this system before performing the following procedure.
PROCEDURE
| 1. | CHECK DTC |
(a) Clear the DTCs.
Chassis > Circumference Monitoring Camera Control Module > Clear DTCs(b) Recheck for DTCs and check that no DTCs are output.
Chassis > Circumference Monitoring Camera Control Module > Trouble Codes| Result | Proceed to |
|---|---|
| All DTCs are not output | A |
| All DTCs are output | B |
| DTC U0266 is output | C |
| DTC U0267 is output | D |
| DTCs U0268 is output | E |
| A |  | USE SIMULATION METHOD TO CHECK |
| C | | GO TO STEP 9 |
| D | | GO TO STEP 10 |
| E | | GO TO STEP 11 |
|
| 2. | CHECK LOCAL BUS |
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N104-3 - N104-9 | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Below 54 Ω) | B |
| NG (70 Ω or higher) | C |
| A | | USE SIMULATION METHOD TO CHECK |
| C | | GO TO STEP 7 |
|
| 3. | CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - NO. 27 JUNCTION CONNECTOR) |
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the N104 No. 27 junction connector.
(c) Connect the N44 parking assist ECU connector.
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N104-3 - N104-9 | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| NG | | REPLACE PARKING ASSIST ECU |
|
| 4. | CHECK HARNESS AND CONNECTOR (SIDE TELEVISION CAMERA ASSEMBLY LH - NO. 27 JUNCTION CONNECTOR) |
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the N104 No. 27 junction connector.
(c) Connect the J34 side television camera assembly LH connector.
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N104-2 - N104-8 | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| NG | | REPLACE SIDE TELEVISION CAMERA ASSEMBLY LH |
|
| 5. | CHECK HARNESS AND CONNECTOR (FRONT TELEVISION CAMERA ASSEMBLY - NO. 27 JUNCTION CONNECTOR) |
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the N104 No. 27 junction connector.
(c) Connect the B5 front television camera assembly connector.
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N104-1 - N104-7 | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| NG | | REPLACE FRONT TELEVISION CAMERA ASSEMBLY |
|
| 6. | CHECK HARNESS AND CONNECTOR (SIDE TELEVISION CAMERA ASSEMBLY RH - NO. 27 JUNCTION CONNECTOR) |
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the N104 No. 27 junction connector.
(c) Connect the J12 side television camera assembly RH connector.
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N104-4 - N104-10 | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| OK | | REPLACE NO. 27 JUNCTION CONNECTOR |
| NG | | REPLACE SIDE TELEVISION CAMERA ASSEMBLY RH |
| 7. | CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - NO. 27 JUNCTION CONNECTOR) |
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the N104 No. 27 junction connector.
(c) Connect the N44 parking assist ECU connector.
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N44-9 (CA2H) - N44-10 (CA2L) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| OK | | REPLACE PARKING ASSIST ECU |
|
| 8. | CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - NO. 27 JUNCTION CONNECTOR) |
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the N104 No. 27 junction connector.
(c) Connect the N44 parking assist ECU connector.
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N104-3 - N104-9 | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| OK | | REPLACE NO. 27 JUNCTION CONNECTOR |
| NG | | REPAIR OR REPLACE HARNESS OR CONNECTOR |
| 9. | CHECK HARNESS AND CONNECTOR (SIDE TELEVISION CAMERA ASSEMBLY LH - NO. 27 JUNCTION CONNECTOR) |
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the J34 side television camera assembly LH connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J34-5 (CANH) - J34-4 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| OK | | REPLACE SIDE TELEVISION CAMERA ASSEMBLY LH |
| NG | | REPAIR OR REPLACE HARNESS OR CONNECTOR |
| 10. | CHECK HARNESS AND CONNECTOR (FRONT TELEVISION CAMERA ASSEMBLY - NO. 27 JUNCTION CONNECTOR) |
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the B5 front television camera assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B5-4 (CANH) - B5-1 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| OK | | REPLACE FRONT TELEVISION CAMERA ASSEMBLY |
| NG | | REPAIR OR REPLACE HARNESS OR CONNECTOR |
| 11. | CHECK HARNESS AND CONNECTOR (SIDE TELEVISION CAMERA ASSEMBLY RH - NO. 27 JUNCTION CONNECTOR) |
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the J12 side television camera assembly RH connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J12-5 (CANH) - J12-4 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| OK | | REPLACE SIDE TELEVISION CAMERA ASSEMBLY RH |
| NG | | REPAIR OR REPLACE HARNESS OR CONNECTOR |
READ NEXT:
CAN Communication Failure (Message Registry) (U1000)
DESCRIPTION If DTC U1000 is stored frequently, duplicate the problem symptoms and perform troubleshooting again even if the DTC is not output when rechecking for DTCs. DTC No. Detection Item DT
"CHK" message(s) are displayed on the SIGNAL CHECK screen.
DESCRIPTION On the SIGNAL CHECK screen, it is possible to check if the signals sent to the parking assist ECU are normal. Click here HINT:
On the SIGNAL CHECK screen, "OK" (blue) is displayed for
SEE MORE:
AVC-LAN Circuit
DESCRIPTION Each unit of the audio and visual system connected to the AVC-LAN (communication bus) transmits signals via AVC-LAN communication. If a short to +B or short to ground occurs in an AVC-LAN communication line, the audio and visual system will not function normally because communication is
Engine Switch
InspectionINSPECTION PROCEDURE 1. INSPECT ENGINE SWITCH (a) Check the resistance. (1) Measure the resistance according to the value(s) in the table below. Standard Resistance: Tester Connection Condition Specified Condition 5 (SS1) - 6 (AGND) 1 (SS2) - 6 (AGND) Not pushed 10 kΩ
