Lexus ES manuals

Lexus ES: Initialization

Lexus ES (XZ10) Service Manual / Vehicle Exterior / Lighting (ext) / Lighting System (for Hv Model) / Initialization

INITIALIZATION

NOTICE:

  • The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during headlight ECU sub-assembly LH removal/installation are shown below. for LED Type Turn Signal Light

    Replaced Part or Performed Procedure

    Necessary Procedures

    Proceed to

    Replacement of the headlight ECU sub-assembly LH

    Synchronize the vehicle information

    SYNCHRONIZE VEHICLE INFORMATION

    Perform headlight ECU sub-assembly LH initialization

    HEADLIGHT ECU SUB-ASSEMBLY LH INITIALIZATION

    Replacement of the rear height control sensor sub-assembly LH, removal and reinstallation of the rear height control sensor sub-assembly LH, replacement of the suspension, etc. have been performed

    Perform headlight ECU sub-assembly LH initialization

    HEADLIGHT ECU SUB-ASSEMBLY LH INITIALIZATION

    Auxiliary battery terminal is disconnected and connected

    Steering sensor zero point calibration

    for Bulb Type Turn Signal Light

    Replaced Part or Performed Procedure

    Necessary Procedures

    Proceed to

    Replacement of the headlight ECU sub-assembly LH or headlight assembly LH*

    Synchronize the vehicle information

    SYNCHRONIZE VEHICLE INFORMATION

    Auxiliary battery terminal is disconnected and connected

    Steering sensor zero point calibration

    • *: for TMMK Made
  • If the steering sensor zero point calibration is not performed, the AFS may not operate correctly.*1
  • If the steering sensor zero point calibration is not performed, the cornering lights may not operate correctly.
  • A new headlight ECU sub-assembly LH cannot operate until the vehicle information is registered.
  • After replacing the headlight ECU sub-assembly LH, it is necessary to perform vehicle information registration and initialization.*1
  • Even if the headlight ECU sub-assembly RH is replaced with a new one, synchronize the vehicle information and initialization are not necessary.*1
  • Even if the headlight ECU sub-assembly RH is replaced with a new one, it is not necessary to synchronize the vehicle information.*2
  • Adjust the headlight aim after initializing the headlight ECU sub-assembly LH.*1

    Click here

  • When a malfunction is detected in the lighting system, rear height control sensor sub-assembly LH signal initialization is impossible. Perform troubleshooting before initialization.*1
  • The lighting system uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure.

    Click here

    • *1: for LED Type Turn Signal Light
    • *2: for Bulb Type Turn Signal Light

SYNCHRONIZE VEHICLE INFORMATION (When using the TECHSTREAM)

NOTICE:

  • Make sure to synchronize the vehicle information before performing initialization.
  • If synchronization fails, make sure to turn the power switch off then back on (IG) before performing synchronization again.

(a) Turn the power switch off.

(b) Connect the Techstream to the DLC3.

(c) Turn the power switch on (IG).

(d) Check that the "Headlight System Uninitialized Visit Your Dealer" warning message is displayed on the multi-information display.

(e) Enter the following menus: Body Electrical / AFS*1 or HL AutoLeveling*2 / Utility / ECU Information Sync.

  • *1: for LED Type Turn Signal Light
  • *2: for Bulb Type Turn Signal Light
Body Electrical > AFS > Utility

Tester Display

ECU Information Sync
Body Electrical > HL AutoLeveling > Utility

Tester Display

ECU Information Sync

(f) Check the display on the Techstream and press "Next".

(g) Check that the "Headlight System Malfunction Visit Your Dealer" warning message continuously blinks 6 times at 2 Hz on the multi-information display.

HINT:

  • If the "Headlight System Malfunction Visit Your Dealer" warning message does not start blinking on the multi-information display after perform the procedure again.
  • If the "Headlight System Malfunction Visit Your Dealer" warning message changes from blinking to displayed on the multi-information display, the rear height control sensor sub-assembly LH may be malfunctioning.

(h) Press "Exit".

(i) Turn the power switch off.

NOTICE:

After synchronizing the vehicle information, initialize the headlight ECU sub-assembly LH.

NOTICE:

  • Make sure to synchronize the vehicle information before performing initialization.
  • If synchronization fails, make sure to turn the power switch off then back on (IG) before performing synchronization again.

SYNCHRONIZE VEHICLE INFORMATION (When not using the TECHSTREAM)

(a) Turn the power switch on (IG).

(b) Check that the "Headlight System Uninitialized Visit Your Dealer" warning message is displayed on the multi-information display.

(c) Using the headlight dimmer switch, turn the low beam headlights on and off 8 times within 20 seconds after turning the power switch on (IG).

NOTICE:

If the low beam headlights illuminate when the power switch is on (IG), shine a light on the automatic light control sensor to turn the low beam headlights off before operating the headlight dimmer switch.

HINT:

If this step cannot be completed within 20 seconds, turn the power switch off. Then, turn the power switch on (IG) and restart the procedure.

(d) Check that the "Headlight System Malfunction Visit Your Dealer" warning message continuously blinks 6 times at 2 Hz on the multi-information display.

HINT:

  • If the "Headlight System Malfunction Visit Your Dealer" warning message does not start blinking on the multi-information display after perform the procedure again.
  • If the "Headlight System Malfunction Visit Your Dealer" warning message changes from blinking to displayed on the multi-information display, turn the power switch off and then on (IG). If "Headlight System Malfunction Visit Your Dealer" is displayed immediately after the power switch is turned on (IG), the rear height control sensor sub-assembly LH may be malfunctioning.

(e) Turn the power switch off.

NOTICE:

After synchronizing the vehicle information, initialize the headlight ECU sub-assembly LH.

HEADLIGHT ECU SUB-ASSEMBLY LH INITIALIZATION (When using the TECHSTREAM)

NOTICE:

Make sure to synchronize the vehicle information before performing initialization.

(a) Prepare vehicle for initialization

  • Unload the vehicle, ensuring that the spare tire, tools and jack are in their original positions.
  • Check that there are no occupants in the vehicle.
  • Turn the light control switch to the DRL OFF*1 or off*2 position.
  • Stop the vehicle on a level surface and keep the vehicle height unchanged.
    • *1: w/ DRL OFF Switch
    • *2: w/o DRL OFF Switch

(b) Check the "Headlight System Malfunction Visit Your Dealer" warning message on the multi-information display.

(1) Turn the power switch on (IG), and check the condition of the "Headlight System Malfunction Visit Your Dealer" warning message on the multi-information display.

OK:

Condition

Specified Condition

The headlight ECU sub-assembly LH has been replaced with a new one.

"Headlight System Malfunction Visit Your Dealer" blinks 6 times at 2 Hz.

Replacement of the rear height control sensor sub-assembly LH, removal and reinstallation of the rear height control sensor sub-assembly LH, replacement of the suspension, etc. have been performed.

"Headlight System Malfunction Visit Your Dealer" is not displayed.

HINT:

If the condition of the "Headlight System Malfunction Visit Your Dealer" warning message is different than listed in the table above, the headlight ECU sub-assembly LH or combination meter assembly may be malfunctioning.

(c) Perform initialization.

(1) Turn the power switch off.

(2) Connect the Techstream to the DLC3.

(3) Turn the power switch on (IG).

(4) Enter the following menus: Body Electrical / AFS*1 or HL AutoLeveling*2 / Utility / Height Sensor Initialization.

  • *1: for LED Type Turn Signal Light
  • *2: for Bulb Type Turn Signal Light
Body Electrical > AFS > Utility

Tester Display

Height Sensor Initialization
Body Electrical > HL AutoLeveling > Utility

Tester Display

Height Sensor Initialization

(5) Check the display on the Techstream and press "Next".

(6) Press "Exit".

(7) Check the condition of the "Headlight System Malfunction Visit Your Dealer" warning message on the multi-information display.

Standard:

Condition

Specified Condition

The headlight ECU sub-assembly LH has been replaced with a new one.

Blinks 6 times at 2 Hz → Continuously blinks 3 times at 2 Hz.

Replacement of the rear height control sensor sub-assembly LH, removal and reinstallation of the rear height control sensor sub-assembly LH, replacement of the suspension, etc. have been performed.

Off → Continuously blinks 3 times at 2 Hz.

HINT:

  • If the "Headlight System Malfunction Visit Your Dealer" warning message is displayed on the multi-information display, the headlight ECU sub-assembly LH may be malfunctioning.
  • If initialization does not finish normally, restart the initialization procedure from step (i).

(8) Check that initialization finishes normally and turn the power switch off.

HINT:

The warning message will blink in the pattern indicating that initialization has completed successfully continuously until the power switch is turned off.

HEADLIGHT ECU SUB-ASSEMBLY LH INITIALIZATION (When not using the TECHSTREAM)

NOTICE:

Make sure to synchronize the vehicle information before performing initialization.

(a) Prepare vehicle for initialization

  • Unload the vehicle, ensuring that the spare tire, tools and jack are in their original positions.
  • Check that there are no occupants in the vehicle.
  • Turn the light control switch to the DRL OFF*1 or off*2 position.
  • Stop the vehicle on a level surface and keep the vehicle height unchanged.
    • *1: w/ DRL OFF Switch
    • *2: w/o DRL OFF Switch

(b) Check the "Headlight System Malfunction Visit Your Dealer" warning message on the multi-information display.

(1) Turn the power switch on (IG), and check the condition of the "Headlight System Malfunction Visit Your Dealer" warning message on the multi-information display.

OK:

Condition

Specified Condition

The headlight ECU sub-assembly LH has been replaced with a new one.

"Headlight System Malfunction Visit Your Dealer" blinks 6 times at 2 Hz.

Replacement of the rear height control sensor sub-assembly LH, removal and reinstallation of the rear height control sensor sub-assembly LH, replacement of the suspension, etc. have been performed.

"Headlight System Malfunction Visit Your Dealer" is not displayed.

HINT:

If the condition of the "Headlight System Malfunction Visit Your Dealer" warning message is different than listed in the table above, the headlight ECU sub-assembly LH or combination meter assembly may be malfunctioning.

(c) Perform initialization.

(1) Turn the power switch and light control switch off.

(2) Cover the automatic light control sensor with a lightproof object.

(3) Perform the following steps within 5 seconds.

  1. Press the power switch 2 times.

    HINT:

    Turn the power switch on (IG).

  2. While pulling the headlight dimmer switch, turn it from DRL OFF*1 or off*2 to AUTO to DRL OFF*1 or off*2 again 3 times or more.

    HINT:

    Check that the parking lights turn from off to on and back off again.

    • *1: w/ DRL OFF Switch
    • *2: w/o DRL OFF Switch
  3. Turn the light control switch off.

HINT:

  • Perform the above operation within 5 seconds.
  • When initialization mode has been entered, "Headlight System Malfunction Visit Your Dealer" warning message on the multi-information display starts blinking at 1 Hz.

(4) Check the condition of the "Headlight System Malfunction Visit Your Dealer" warning message on the multi-information display.

Standard:

Condition

Specified Condition

The headlight ECU sub-assembly LH has been replaced with a new one.

Blinks 6 times at 2 Hz → Continuously blinks 3 times at 2 Hz.

Replacement of the rear height control sensor sub-assembly LH, removal and reinstallation of the rear height control sensor sub-assembly LH, replacement of the suspension, etc. have been performed.

Off → Continuously blinks 3 times at 2 Hz.

HINT:

  • If the "Headlight System Malfunction Visit Your Dealer" warning message is displayed on the multi-information display, the headlight ECU sub-assembly LH may be malfunctioning.
  • If initialization does not finish normally, restart the initialization procedure from step (i).

(5) Check that initialization finishes normally and turn the power switch off.

HINT:

The warning message will blink in the pattern indicating that initialization has completed successfully continuously until the power switch is turned off.

READ NEXT:

 Problem Symptoms Table

PROBLEM SYMPTOMS TABLE NOTICE: Before replacing the main body ECU (multiplex network body ECU), refer to Registration. Click here If the headlight ECU sub-assembly LH has been replaced, it is

 Terminals Of Ecu

TERMINALS OF ECU CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (a) Disconnect the instrument panel junction block assembly and main body ECU (multiplex

 Dtc Check / Clear

DTC CHECK / CLEAR CHECK FOR DTC (MAIN BODY) (a) Connect the Techstream to the DLC3. (b) Turn the power switch on (IG). (c) Turn the Techstream on. (d) Enter the following menus: Body Electrical / Main

SEE MORE:

 System Diagram

SYSTEM DIAGRAM Transmitting ECU (Transmitter) Receiving ECU Signal Communication Method Skid control ECU (brake actuator assembly) Steering angle sensor Steering angle sensor request signal CAN communication line Steering angle sensor Skid control ECU (brake actuator a

 Precaution

PRECAUTION PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE BATTERY TERMINAL NOTICE: When disconnecting the cable from the negative (-) battery terminal, initialize the following systems after the cable is reconnected. System Name See Procedure Lane Control System (for Gasoline Model)

© 2016-2024 Copyright www.lexguide.net