Lexus ES: How To Proceed With Troubleshooting
CAUTION / NOTICE / HINT
HINT:
- Use the following procedure to troubleshoot the sliding roof system.
- *: Use the Techstream.
PROCEDURE
| 1. | VEHICLE BROUGHT TO WORKSHOP |
|
.gif)
| 2. | CUSTOMER PROBLEM ANALYSIS |
HINT:
- In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
- Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
-
The following 5 items are important points for problem analysis:
What
Vehicle model, system name
When
Date, time, occurrence frequency
Where
Road conditions
Under what conditions?
Driving conditions, weather conditions
How did it happen?
Problem symptoms
|
| 3. | PRE-CHECK |
(a) Measure the battery voltage.
Standard Voltage:
11 to 14 V
If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.
(b) Check the fuses and relays.
(c) Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.
|
| 4. | INSPECT COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM* |
(a) Using the Techstream, check for CAN communication system DTCs.
Click here .gif)
| Result | Proceed to |
|---|---|
| CAN DTCs are not output | A |
| CAN DTCs are output | B |
| B | .gif) | GO TO CAN COMMUNICATION SYSTEM |
|
| 5. | INSPECT COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM* |
(a) Using the Techstream, check for LIN communication system DTCs.
Click here
| Result | Proceed to |
|---|---|
| LIN DTCs are not output | A |
| LIN DTCs are output | B |
| B | | GO TO LIN COMMUNICATION SYSTEM |
|
| 6. | CHECK FOR DTC* |
(a) Check for DTCs and make a note of any codes that are output.
Click here
(b) Clear the DTCs.
Body Electrical > Sliding Roof > Clear DTCs(c) Recheck for DTCs.
Body Electrical > Sliding Roof > Trouble Codes| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
| B | | GO TO DIAGNOSTIC TROUBLE CODE CHART |
|
| 7. | PROBLEM SYMPTOMS TABLE |
(a) Refer to Problem Symptoms Table.
Click here
| Result | Proceed to |
|---|---|
| Fault is not listed in Problem Symptoms Table | A |
| Fault is listed in Problem Symptoms Table | B |
| B | | GO TO STEP 9 |
|
| 8. | OVERALL ANALYSIS AND TROUBLESHOOTING* |
(a) Operation Check
Click here
(b) Terminals of ECU
Click here
(c) Data List / Active Test
Click here
(d) Inspection
|
| 9. | ADJUST, REPAIR OR REPLACE |
(a) Check if the sliding roof drive gear sub-assembly has been replaced, or the sliding roof glass sub-assembly or sliding roof drive cable sub-assembly has been adjusted, or removed and installed.
| Result | Proceed to |
|---|---|
| The sliding roof drive gear sub-assembly has been replaced, or the sliding roof glass sub-assembly or sliding roof drive cable sub-assembly has been adjusted, or removed and installed. | A |
| The sliding roof drive gear sub-assembly has not been replaced, and the sliding roof glass sub-assembly and sliding roof drive cable sub-assembly have not been adjusted, or removed and installed. | B |
| B | | GO TO STEP 11 |
|
| 10. | INITIALIZE SLIDING ROOF SYSTEM |
(a) Initialize the sliding roof ECU (sliding roof drive gear sub-assembly).
Click here
|
| 11. | CONFIRMATION TEST |
| NEXT | | END |
READ NEXT:
Operation Check
OPERATION CHECK CHECK AUTO OPERATION FUNCTION NOTICE:
Make sure that initialization has been completed before performing this inspection.
Click here
The sliding roof auto operation can be custo
Customize Parameters
CUSTOMIZE PARAMETERS CUSTOMIZE SLIDING ROOF SYSTEM HINT: The following items can be customized. NOTICE:
When the customer requests a change in a function, first make sure that the function can be c
Initialization
INITIALIZATION INITIALIZE SLIDING ROOF SYSTEM NOTICE:
When the sliding roof glass sub-assembly or sliding roof drive cable sub-assembly is adjusted or removed/installed, or the sliding roof drive g
SEE MORE:
Internal Control Module Software Incompatibility Invalid / Incompatible Software Component (U030057)
DESCRIPTION Forward recognition camera receives the vehicle information from the hybrid vehicle control ECU via CAN communication. DTC U030057 is stored when the vehicle information from the hybrid vehicle control ECU and that stored in the forward recognition camera do not match. DTC No. Detec
Components
COMPONENTS ILLUSTRATION *1 REAR NO. 1 STABILIZER BAR BRACKET *2 CANISTER (CHARCOAL CANISTER ASSEMBLY) *3 LEAK DETECTION PUMP SUB-ASSEMBLY *4 FUEL TANK VENT HOSE SUB-ASSEMBLY *5 FUEL TANK VENT HOSE *6 PURGE LINE HOSE *7 CHARCOAL CANISTER SUB-ASSEMBLY *8 CLIP
