Lexus ES: How To Proceed With Troubleshooting
CAUTION / NOTICE / HINT
HINT:
- Use the following procedure to troubleshoot the lighting system.
- *: Use the Techstream.
PROCEDURE
| 1. | VEHICLE BROUGHT TO WORKSHOP |
|
.gif)
| 2. | CUSTOMER PROBLEM ANALYSIS |
HINT:
- In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
- Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
-
The following 5 items are important points for problem analysis:
What
Vehicle model, system name
When
Date, time, occurrence frequency
Where
Road conditions
Under what conditions?
Driving conditions, weather conditions
How did it happen?
Problem symptoms
|
| 3. | PRE-CHECK |
(a) Measure the battery voltage.
Standard Voltage:
11 to 14 V
If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.
(b) Check the fuses and relays.
(c) Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.
|
| 4. | CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM* |
(a) Using the Techstream, check for CAN communication system DTCs.
Click here .gif)
| Result | Proceed to |
|---|---|
| CAN DTCs are not output (for LED Type Turn Signal Light) | A |
| CAN DTCs are not output (for Bulb Type Turn Signal Light) | B |
| CAN DTCs are output | C |
| B | .gif) | GO TO STEP 6 |
| C | | GO TO CAN COMMUNICATION SYSTEM |
|
| 5. | CHECK FOR DTC* |
(a) Check for DTCs.
Body Electrical > Main Body > Trouble Codes Body Electrical > AFS > Trouble Codes Body Electrical > AFS (Sub) > Trouble Codes Body Electrical > Front Recognition Camera (Front Lighting Control) > Trouble Codes| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
| A | | GO TO STEP 7 |
| B | | GO TO DIAGNOSTIC TROUBLE CODE CHART |
| 6. | CHECK FOR DTC* |
(a) Check for DTCs.
Body Electrical > Main Body > Trouble Codes Body Electrical > HL AutoLeveling > Trouble Codes Body Electrical > HL AutoLeveling (Sub) > Trouble Codes Body Electrical > Front Recognition Camera (Front Lighting Control) > Trouble Codes| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
| B | | GO TO DIAGNOSTIC TROUBLE CODE CHART |
|
| 7. | CHECK VEHICLE CONTROL HISTORY* |
(a) Using the Techstream, check for Vehicle Control History (RoB).
Body Electrical > Front Recognition Camera (Front Lighting Control) > Utility| Tester Display |
|---|
| Vehicle Control History (RoB) |
NOTICE:
Make sure to record the output Vehicle Control History.
| Result | Proceed to |
|---|---|
| Vehicle Control History codes are not output | A |
| Vehicle Control History code X2020 and/or X204D is output | B |
| Vehicle Control History codes other than X2020 and X204D are output | C |
| B | | GO TO VEHICLE CONTROL HISTORY (Check Details of Code X2020 or X204D) |
| C | | GO TO STEP 12 |
|
| 8. | PROBLEM SYMPTOMS TABLE |
(a) Refer to Problem Symptoms Table.
Click here
| Result | Proceed to |
|---|---|
| Fault is not listed in Problem Symptoms Table | A |
| Fault is listed in Problem Symptoms Table | B |
| B | | GO TO PROBLEM SYMPTOMS TABLE |
|
| 9. | OVERALL ANALYSIS AND TROUBLESHOOTING* |
(a) Operation Check.
Click here
(b) Terminals of ECU.
Click here
(c) Data List / Active Test.
Click here
(d) On-vehicle Inspection.
(e) Inspection.
|
| 10. | ADJUST, REPAIR OR REPLACE |
|
| 11. | CONFIRMATION TEST |
| NEXT | | END |
| 12. | CHECK VEHICLE CONTROL HISTORY* |
(a) Clear Vehicle Control History
(1) Clear the Vehicle Control History.
Body Electrical > Front Recognition Camera (Front Lighting Control) > Utility| Tester Display |
|---|
| Vehicle Control History (RoB) |
(b) Check Vehicle Control History
(1) Using the Techstream, check the Vehicle Control History (RoB).
Body Electrical > Front Recognition Camera (Front Lighting Control) > Utility| Tester Display |
|---|
| Vehicle Control History (RoB) |
| Result | Proceed to |
|---|---|
| Vehicle Control History (RoB) codes are not output | A |
| Vehicle Control History (RoB) codes are output | B |
| A | | USE SIMULATION METHOD TO CHECK |
| B | | GO TO VEHICLE CONTROL HISTORY |
READ NEXT:
Operation Check
OPERATION CHECK AUTOMATIC LIGHT CONTROL SYSTEM OPERATION CHECK NOTICE: Make sure that the customize settings are set to default when performing the automatic light control system operation check. Clic
Customize Parameters
CUSTOMIZE PARAMETERS CUSTOMIZE LIGHTING SYSTEM (EXT) NOTICE:
When the customer requests a change in a function, first make sure that the function can be customized.
Be sure to make a note of the
Initialization
INITIALIZATION NOTICE:
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during headlight
SEE MORE:
Ignition Circuit
DESCRIPTION A direct ignition system is used on this vehicle. The direct ignition system is a 1 cylinder ignition system which ignites one cylinder with one ignition coil. In the 1 cylinder ignition system, one spark plug is connected to the end of the secondary winding. High voltage is generated in
Driver Side Power Mirror cannot be Adjusted with Power Mirror Switch
DESCRIPTION The outer mirror switch assembly sends the mirror adjust switch signals to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) then sends the received mirror adjust switch signals to the outer mirror control ECU assembly (driver door) via CAN co
