Lexus ES: How To Proceed With Troubleshooting
CAUTION / NOTICE / HINT
HINT:
- Use the following procedure to troubleshoot the parking assist monitor system.
- *: Use the Techstream.
PROCEDURE
| 1. | VEHICLE BROUGHT TO WORKSHOP |
|
.gif)
| 2. | CUSTOMER PROBLEM ANALYSIS |
(a) Ask the customer about the problems and the conditions at the time the malfunction occurred to make sure the problem symptom was not temporarily caused by radio waves in the surrounding environment.
HINT:
The parking assist monitor display may be temporarily distorted due to radio waves around the vehicle.
| Problem Symptom | Cause |
|---|---|
| *: DTCs output as "Hist" will not be output again after DTCs are cleared. | |
| Both of the following conditions are met:
| The display may be temporarily distorted when the vehicle is close to an object that transmits radio waves, such as a telecommunication tower, an airport or a truck equipped with a transceiver. |
|
| 3. | INSPECT AUXILIARY BATTERY VOLTAGE |
(a) Measure the auxiliary battery voltage.
Standard Voltage:
11 to 14 V
If the voltage is below 11 V, replace or recharge the auxiliary battery before proceeding to the next step.
|
| 4. | SYSTEM CHECK |
(a) Check the vehicle specification.
| Result | Proceed to |
|---|---|
| w/ Navigation System | A |
| w/o Navigation System | B |
| B | .gif) | GO TO STEP 6 |
|
| 5. | CHECK NAVIGATION SYSTEM |
(a) Refer to Navigation System.
Click here .gif)
| Result | Proceed to |
|---|---|
| Navigation system is normal | A |
| Navigation system is abnormal | B |
| A | | GO TO STEP 7 |
| B | | GO TO NAVIGATION SYSTEM |
| 6. | CHECK AUDIO AND VISUAL SYSTEM |
(a) Refer to Audio and Visual System.
Click here
| Result | Proceed to |
|---|---|
| Audio and visual system is normal | A |
| Audio and visual system is abnormal | B |
| B | | GO TO AUDIO AND VISUAL SYSTEM |
|
| 7. | CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM* |
(a) Use the Techstream to check if the CAN communication system is functioning normally.
Click here
| Result | Proceed to |
|---|---|
| CAN communication system DTCs are not output | A |
| CAN communication system DTCs are output | B |
| B | | GO TO CAN COMMUNICATION SYSTEM |
|
| 8. | CHECK FOR DTC* |
(a) Check for DTCs and make a note of any codes that are output.
Chassis > Rear Camera > Trouble Codes(b) Clear the DTCs.
Chassis > Rear Camera > Clear DTCs(c) Recheck for DTCs. Try to prompt the DTC by simulating the original activity that the DTC suggests.
Chassis > Rear Camera > Trouble Codes| Result | Proceed to |
|---|---|
| No DTCs are output | A |
| DTCs are output | B |
| B | | GO TO STEP 11 |
|
| 9. | PROBLEM SYMPTOMS TABLE |
(a) Refer to Problem Symptoms Table.
Click here
| Result | Proceed to |
|---|---|
| Fault is not listed in Problem Symptoms Table | A |
| Fault is listed in Problem Symptoms Table | B |
| B | | GO TO STEP 11 |
|
| 10. | OVERALL ANALYSIS AND TROUBLESHOOTING |
(a) Diagnosis System
Click here
(b) Terminals of ECU
Click here
(c) Data List / Active Test
Click here
|
| 11. | ADJUST, REPAIR OR REPLACE |
|
| 12. | CONFIRMATION TEST |
| NEXT | | END |
READ NEXT:
Image from Camera for Parking Assist Monitor is Abnormal
DESCRIPTION The video signal from the rear television camera assembly is transmitted to the multi-display assembly. WIRING DIAGRAM CAUTION / NOTICE / HINT NOTICE:
If the cable was disconnected fro
Initialization
INITIALIZATION INITIALIZE PARKING ASSIST MONITOR SYSTEM (a) When "!" mark is displayed on the image of the area behind the vehicle, perform the following procedure to correct the steering angle neutra
Parts Location
PARTS LOCATION ILLUSTRATION *1 HYBRID VEHICLE CONTROL ECU *2 REAR TELEVISION CAMERA ASSEMBLY *3 BLIND SPOT MONITOR SENSOR RH (w/ Blind Spot Monitor System) *4 BLIND SPOT MONITOR SE
SEE MORE:
Removal
REMOVAL CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during outer rear view mirror assembly with cover removal/installation are shown below. Necessary Procedure Af
High Voltage Power Resource Internal Electronic Failure (P1C8549)
DESCRIPTION The hybrid vehicle control ECU monitors the system internal operation, it will store a DTC and perform fail-safe control if it detects the following malfunction. DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate P1C8549 High Voltage Power
