Lexus ES: Error in Matching of ECUs (C1567)
DESCRIPTION
The power steering ECU (rack and pinion power steering gear assembly) determines whether an incompatible ECM or skid control ECU (brake actuator assembly) is installed based on the identification information.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Return-to-normal Condition | Note |
|---|---|---|---|---|---|---|
| C1567 | Error in Matching of ECUs |
|
| EPS warning light: Comes on | Engine switch on (IG) again | - |
CAUTION / NOTICE / HINT
NOTICE:
If the rack and pinion power steering gear assembly has been replaced, perform assist map writing and torque sensor zero point calibration.
Click here .gif)
PROCEDURE
| 1. | CHECK RELATED PART |
(a) Confirm if the related part has the correct part number.
| Related Part | ECM |
| Skid control ECU (Brake actuator assembly) |
NOTICE:
When removing the related part to check it, be sure to follow the appropriate procedures and precautions.
-
ECM
for 2GR-FKS: Click here
for A25A-FKS: Click here
-
Skid control ECU (Brake actuator assembly)
Click here
| Result | Proceed to |
|---|---|
| The related part has the correct part number. | A |
| The related part has an incorrect part number. | B |
| B | .gif) | GO TO STEP 3 |
|
.gif)
| 2. | CHECK FOR DTC |
(a) Select Health Check on the Techstream screen and check if system DTCs of the related part are output.
HINT:
If system DTCs of the related part are stored, assist map writing to the power steering ECU (rack and pinion power steering gear assembly) may not be performed properly.
| Result | Proceed to |
|---|---|
| System DTCs of the related part are output. | A |
| System DTCs of the related part are not output. | B |
| A | | REPAIR CIRCUIT INDICATED BY OUTPUT CODE |
| B | | REPLACE RACK AND PINION POWER STEERING GEAR ASSEMBLY |
| 3. | REPLACE RELATED PART WITH PART THAT HAS CORRECT PART NUMBER |
(a) Replace the related part with one that has the correct part number.
-
ECM
for 2GR-FKS: Click here
for A25A-FKS: Click here
-
Skid control ECU (Brake actuator assembly)
Click here
|
| 4. | CHECK FOR DTC |
(a) Check for DTCs.
Chassis > EMPS > Trouble Codes| Result | Proceed to |
|---|---|
| DTCs are not output. | A |
| DTCs are output. | B |
| A | | END |
| B | | REPLACE RACK AND PINION POWER STEERING GEAR ASSEMBLY |
READ NEXT:
Assist Map Number Un-Writing (C1581)
DESCRIPTION This DTC will be stored if the power steering ECU (rack and pinion power steering gear assembly) determines that the assist map is not written in the ECU. DTC No. Detection Item DTC
Assist Map Number Un-Writing (C1581)
DESCRIPTION This DTC will be stored if the power steering ECU (rack and pinion power steering gear assembly) determines that the assist map is not written in the ECU. DTC No. Detection Item DTC
Assist Map Number Mismatch (C1582)
DESCRIPTION When an incorrect ECM, skid control ECU (brake actuator assembly) or AVS ECU (Absorber control ECU) (w/ Adaptive Variable Suspension System) is installed after the assist map has been writ
SEE MORE:
Components
COMPONENTS ILLUSTRATION *1 AIR FUEL RATIO SENSOR - - N*m (kgf*cm, ft.*lbf): Specified torque * For use with SST
Problem Symptoms Table
PROBLEM SYMPTOMS TABLE NOTICE: Before replacing the main body ECU (multiplex network body ECU), refer to Registration. for Gasoline Model: Click here for HV Model: Click here HINT: Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the
