Lexus ES: Data List / Active Test
DATA LIST / ACTIVE TEST
DATA LIST
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Sliding Roof or Main Body / Data List.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > Sliding Roof > Data List| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Open Switch | Sliding roof open switch signal | OFF or ON | OFF: Sliding roof switch not slid backward ON: Sliding roof switch slid backward | - |
| Close Switch | Sliding roof close switch signal | OFF or ON | OFF: Sliding roof switch not slid forward ON: Sliding roof switch slid forward | - |
| Up Switch | Roof sunshade close switch signal | OFF or ON | OFF: Roof sunshade switch not slid forward ON: Roof sunshade switch slid forward | - |
| Down Switch | Roof sunshade open switch signal | OFF or ON | OFF: Roof sunshade switch not slid backward ON: Roof sunshade switch slid backward | - |
| Front SW Auto Operation | Sliding roof auto operation function | OFF or ON | Customize setting displayed | - |
| Hall IC1 Pulse | Hall IC1 pulse output | Lo or Hi | Lo and Hi repeat during motor operation | Lo: Hall IC1 output is low Hi: Hall IC1 output is high |
| Hall IC1 Status | Status of Hall IC1 | Normal or Error | Normal: Hall IC1 normal Error: Hall IC1 not normal | - |
| Hall IC2 Pulse | Hall IC2 pulse output | Lo or Hi | Lo and Hi repeat during motor operation | Lo: Hall IC2 output is low Hi: Hall IC2 output is high |
| Hall IC2 Status | Status of Hall IC2 | Normal or Error | Normal: Hall IC2 normal Error: Hall IC2 not normal | - |
| Ignition (MPX) | Engine switch signal (LIN signal) | OFF or ON | OFF: Engine switch off ON: Engine switch on (IG) | - |
| Door Key Close Operation | Key-linked sliding roof close signal | OFF or ON | OFF: Driver door key cylinder not turned ON: Driver door key cylinder turned and held at the lock position | - |
| Door Key Open Operation | Key-linked sliding roof open signal | OFF or ON | OFF: Driver door key cylinder not turned ON: Driver door key cylinder turned and held at the unlock position | - |
| Wireless Open Operation | Wireless transmitter-linked sliding roof open signal | OFF or ON | OFF: Wireless transmitter unlock switch not pressed ON: Wireless transmitter unlock switch pressed and held | - |
| Key Off Permission | Key-off sliding roof operation permit signal | OFF or ON | OFF: Any status except "ON" status ON: Front doors are not opened within 45 seconds after engine switch turned off | - |
| Door Key Related Operation | Key-linked sliding roof open function operating direction | Slide or Tilt | Customization status displayed | - |
| Wireless Key Rel Operation | Wireless transmitter-linked sliding roof open function operating direction | Slide or Tilt | Customization status displayed | - |
| Open Switch Failure(Past) | Sliding roof open switch stuck signal (Past) | OFF or ON | OFF: No sliding roof switch stuck signal (Past) ON: Sliding roof switch stuck signal (Past) | - |
| Close Switch Failure(Past) | Sliding roof close switch stuck signal (Past) | OFF or ON | OFF: No sliding roof switch stuck signal (Past) ON: Sliding roof switch stuck signal (Past) | - |
| Up Switch Failure(Past) | Roof sunshade open switch stuck signal (Past) | OFF or ON | OFF: No roof sunshade switch stuck signal (Past) ON: Roof sunshade switch stuck signal (Past) | - |
| Down Switch Failure(Past) | Roof sunshade close switch stuck signal (Past) | OFF or ON | OFF: No roof sunshade switch stuck signal (Past) ON: Roof sunshade switch stuck signal (Past) | - |
| Open Switch Failure(Current) | Sliding roof open switch stuck signal (Current) | OFF or ON | OFF: No sliding roof switch stuck signal (Current) ON: Sliding roof switch stuck signal (Current) | - |
| Close Switch Failure(Current) | Sliding roof close switch stuck signal (Current) | OFF or ON | OFF: No roof sunshade switch stuck signal (Current) ON: Roof sunshade switch stuck signal (Current) | - |
| Up Switch Failure(Current) | Roof sunshade open switch stuck signal (Current) | OFF or ON | OFF: No roof sunshade switch stuck signal (Current) ON: Roof sunshade switch stuck signal (Current) | - |
| Down Switch Failure(Current) | Roof sunshade close switch stuck signal (Current) | OFF or ON | OFF: No roof sunshade switch stuck signal (Current) ON: Roof sunshade switch stuck signal (Current) | - |
| Suggestion Service Function | Availability of suggestion function* | OFF or ON | ON: w/ Suggestion function OFF: w/o Suggestion function | Not applicable |
| Number of Trouble Codes | Number of trouble codes | Min.: 0 to Max.: 255 | Number of DTCs is displayed | - |
- *: Although this item is displayed on the Techstream, it is not applicable to this vehicle.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| IG SW | Engine switch status | OFF or ON | OFF: Engine switch off ON: Engine switch on (IG) | "OFF" is displayed even though the engine switch is turned on (ACC). |
| FR Door Courtesy SW | Front door courtesy light switch assembly (for RH) signal | OFF or ON | OFF: Front door RH closed ON: Front door RH open | - |
| FL Door Courtesy SW | Front door courtesy light switch assembly (for LH) signal | OFF or ON | OFF: Front door LH closed ON: Front door LH open | - |
| Door Key P/W Up | Key-linked sliding roof close function | OFF or ON | Customization status displayed | - |
| Door Key P/W Down | Key-linked sliding roof open function | OFF or ON | Customization status displayed | - |
| P/W Down W/ Transmit | Wireless transmitter linked sliding roof open function | OFF or ON | Customization status displayed | - |
| Slide Roof Open Warning | Sliding roof open warning | OFF or ON | Customize setting displayed | - |
| Communication Slide Roof | Connection status between sliding roof ECU (sliding roof drive gear assembly) and main body ECU (multiplex network body ECU) | STOP or OK | STOP: Communication stopped OK: Normal communication | - |
| The Number of DTC | Number of trouble codes | Min.: 0 to Max.: 255 | Number of DTCs is displayed | - |
ACTIVE TEST
HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Sliding Roof or Sliding Sunshade / Active Test.
(e) Perform the Active Test according to the display on the Techstream.
Body Electrical > Sliding Roof > Active Test| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Slide Roof | Operate sliding roof motor | OFF / Opn/Dwn / Clos/Up | - |
READ NEXT:
Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART Panoramic Moon Roof System DTC No. Detection Item Link B2341 Sensor (Motor) Failure B2342 Switch Failure B2343 Position Initialization
Sensor (Motor) Failure (B2341,B2344)
DESCRIPTION When the sliding roof ECU (sliding roof drive gear assembly) detects a motor malfunction and the sliding roof operation is stopped, DTC B2341 is stored. When the sliding roof ECU (sliding
Switch Failure (B2342)
DESCRIPTION This DTC is stored when the sliding roof ECU (sliding roof drive gear assembly) detects that the panoramic moon roof switch (map light sub-assembly) is stuck for 30 seconds or more. DTC
SEE MORE:
Installation
INSTALLATION PROCEDURE 1. INSTALL BACK-UP BATTERY (a) Connect the connector and install the back-up battery with the "TOP" mark facing upward as shown in the illustration. Install in this Direction NOTICE: Make sure that the connector is connected securely. (b) Engage the 2 guides and 3 cl
Fail-safe Chart
FAIL-SAFE CHART DTC Trouble Area Brake System Warning Light (Yellow) Parking Brake Indicator Light (Red) Fail-safe Deactivation Condition C1245 Deceleration sensor data malfunction Illuminates Normal 20 seconds after power switch turned off C13A0 Open in power supply rel
