Lexus ES: Data List / Active Test
DATA LIST / ACTIVE TEST
DATA LIST
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Main Body or Smart Access / Data List.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > Main Body > Data List| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Communication D-Door Motor | Connection status between power window regulator motor assembly (driver door) and main body ECU (multiplex network body ECU) | OK or STOP | OK: Connected STOP: Not Connected | DTC is output if an error occurs in LIN communication. |
| Communication P-Door Motor | Connection status between power window regulator motor assembly (front passenger door) and main body ECU (multiplex network body ECU) | OK or STOP | OK: Connected STOP: Not Connected | DTC is output if an error occurs in LIN communication. |
| Communication RR-Door Motor | Connection status between power window regulator motor assembly (rear RH door) and main body ECU (multiplex network body ECU) | OK or STOP | OK: Connected STOP: Not Connected | DTC is output if an error occurs in LIN communication. |
| Communication RL-Door Motor | Connection status between power window regulator motor assembly (rear LH door) and main body ECU (multiplex network body ECU) | OK or STOP | OK: Connected STOP: Not Connected | DTC is output if an error occurs in LIN communication. |
| Communication Slide Roof | Connection status between main body ECU (multiplex network body ECU) and sliding roof ECU (sliding roof drive gear sub-assembly | OK or STOP | OK: Connected STOP: Not Connected | DTC is output if an error occurs in LIN communication. |
| Communication Master SW | Connection status between multiplex network master switch assembly and main body ECU (multiplex network body ECU) | OK or STOP | OK: Connected STOP: Not Connected | DTC is output if an error occurs in LIN communication. |
| Communication Double Locking | Connection status between double lock door control relay assembly and main body ECU (multiplex network body ECU)* | OK or STOP | OK: Connected STOP: Not Connected | Not applicable |
| The Number of DTC | Number of DTCs | 0 to 255 | Number of stored DTCs | - |
- *: Although the item is displayed on the Techstream, it is not applicable to this vehicle.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| # Codes | Number of DTCs | 0 to 255 | Number of stored DTCs | - |
READ NEXT:
Diagnosis System
DIAGNOSIS SYSTEM DESCRIPTION The main body ECU (multiplex network body ECU) and certification ECU (smart key ECU assembly) control the LIN communication system. LIN communication system data and Diagn
Dtc Check / Clear
DTC CHECK / CLEAR CHECK DTC (a) Connect the Techstream to the DLC3. (b) Turn the power switch on (IG). (c) Turn the Techstream on. (d) Enter the following menus: Body Electrical / Main Body or Smart A
Terminals Of Ecu
TERMINALS OF ECU CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (a) Disconnect the MB main body ECU (multiplex network body ECU) connector. Click here
SEE MORE:
Problem Symptoms Table
PROBLEM SYMPTOMS TABLE HINT:
Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspect
Height Sensor Initialization Incomplete (B2450)
DESCRIPTION The headlight ECU sub-assembly LH stores this DTC if initialization has not been performed after it was replaced. DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from B2450 Height Sensor Initialization Incomplete
The engine switch is on (IG).
