Lexus ES: Data List / Active Test
DATA LIST / ACTIVE TEST
DATA LIST
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Chassis / Rear Camera / Data List.
(e) Read the Data List according to the display on the Techstream.
Chassis > Rear Camera > Data List| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Video Output Status | Output condition of video signal | OK or NG | OK: Output condition of video signal is normal NG: Output condition of video signal is abnormal | - |
| Destination Data Check | Verification of destination data | OK or NG | OK: Data verification normal NG: Data verification abnormal | - |
| RHD/LHD Signal Check | Verification of RHD/LHD signal | OK or NG | OK: Output condition of RHD/LHD signal is normal NG: Output condition of RHD/LHD signal is abnormal | - |
| Circumference Monitoring System Type Check | Verification of rear television camera assembly signal | OK or NG | OK: Rear television camera assembly normal NG: Rear television camera assembly abnormal | - |
| EEPROM Status (Initial read) | Rear television camera assembly information | OK or NG | OK: Rear television camera assembly normal NG: Rear television camera assembly abnormal | - |
| CPU Communication Status | Rear television camera assembly information | OK or NG | OK: Rear television camera assembly normal NG: Rear television camera assembly abnormal | - |
| Number of DTC | Number of stored DTCs | min.: 0, max.: 255 | Number of DTCs will be displayed | - |
| Current Key Cycle | Cumulative number of times the power switch was turned on (IG) | Min.: 0, Max.: 65535 time | Cumulative number of times the power switch was turned on (IG) will be displayed | - |
| Current Key Cycle Elapsed Time | Time elapsed since the power switch was turned on (IG) | Min.: 0, Max.: 1677721.5 s | Time elapsed since the power switch was turned on (IG) will be displayed | - |
READ NEXT:
Diagnosis System
DIAGNOSIS SYSTEM PARKING ASSIST MONITOR SYSTEM DIAGNOSTIC MODE (a) In diagnostic mode for the parking assist monitor system, signals received by the radio receiver assembly can be checked and the park
Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART Parking Assist Monitor System DTC No. Detection Item Link C1611 ECU Malfunction C1621 Back Camera Power Supply Failure C1622 Back Camer
Dtc Check / Clear
DTC CHECK / CLEAR CHECK DTC (a) Connect the Techstream to the DLC3. (b) Turn the power switch on (IG). (c) Turn the Techstream on. (d) Enter the following menus: Chassis / Rear Camera / Trouble Codes.
SEE MORE:
Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART Parking Assist Monitor System DTC No. Detection Item Link C1611 ECU Malfunction C1621 Back Camera Power Supply Failure C1622 Back Camera Disconnected C1625 Open or Short in Steering Angle Sensor +B C1626 Steering
Operation Check
OPERATION CHECK PKSB OFF INDICATOR LIGHT OPERATION CHECK (a) Turn the engine switch on (IG). (b) Turn the parking support brake system off and confirm that the PKSB OFF indicator in the combination meter illuminates. HINT: If the parking support brake system is not set to off in the customize setti
