Lexus ES: D-Seat ECU Vehicle Information Reading/Writing Process Malfunction (B15F8)
DESCRIPTION
This DTC is stored when items controlled by the main body ECU (multiplex network body ECU) cannot be customized via the navigation system vehicle customization screen.
HINT:
The main body ECU (multiplex network body ECU) controls the front power seat control system (w/ Memory) related items that are customizable via the multi-display assembly screen.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B15F8 | D-Seat ECU Vehicle Information Reading/Writing Process Malfunction | Main body ECU (multiplex network body ECU) vehicle setting processing malfunction |
|
CAUTION / NOTICE / HINT
NOTICE:
-
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.
Click here
.gif)
-
When replacing the radio receiver assembly, always replace it with a new one. If a radio receiver assembly which was installed to another vehicle is used, the following may occur:
- A communication malfunction DTC may be stored.
- The radio receiver assembly may not operate normally.
-
Before replacing the main body ECU (multiplex network body ECU), refer to Registration.
Click here
PROCEDURE
| 1. | CHECK CAN COMMUNICATION SYSTEM |
(a) Use the Techstream to check if the CAN communication system is functioning normally.
Click here
OK:
CAN communication DTCs are not output.
| NG |  | GO TO CAN COMMUNICATION SYSTEM |
|
| 2. | CHECK FRONT POWER SEAT CONTROL SYSTEM (w/ Memory) |
(a) Check if the front power seat control system (w/ Memory) is malfunctioning.
Click here
HINT:
Customization may not be possible depending on the malfunction in the front power seat control system (w/ Memory).
OK:
No malfunctions are present in the front power seat control system (w/ Memory).
| NG | | GO TO FRONT POWER SEAT CONTROL SYSTEM (w/ Memory) |
|
| 3. | CHECK CUSTOMIZE ITEMS |
(a) Display the "Vehicle Customization" screen.
(b) Make a note of the customizable items for each main body ECU (multiplex network body ECU).
HINT:
The items shown as customizable via the navigation system vehicle customization screen can also be changed using the Techstream. In the following step, the Techstream will be used.
(1) To match-up the items on the multi-display assembly with the items on the Techstream, check the customize parameters list for the front power seat control system (w/ Memory) related items that can be customized via the multi-display assembly screen.
Click here
(c) Using the Techstream, check that it is possible to change the settings of the customize parameters that are available for customization via the multi-display assembly screen.
OK:
The items available for customization via the multi-display assembly screen can be customized successfully using the Techstream.
| OK | | REPLACE RADIO RECEIVER ASSEMBLY |
| NG | | REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
READ NEXT:
XM Tuner Antenna Disconnected (B15FE,B15FF)
DESCRIPTION These DTCs are stored when a malfunction occurs in the telephone antenna assembly which is connected to the radio receiver assembly. DTC No. Detection Item DTC Detection Condition
GVIF Disconnected (from Extension Module to H/U) (B153A)
DESCRIPTION The radio receiver assembly and navigation ECU are connected via video signal (digital) lines. This DTC is stored when a video signal (digital) line is disconnected. DTC No. Detection
Touch Pad Vibration Driver Malfunction (B155A)
DESCRIPTION This DTC is stored if the remote touch (remote operation controller assembly) detects a malfunction in itself, such as internal hardware failure or remote touch screen vibration driver mal
SEE MORE:
Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART Active Noise Control System DTC No. Detection Item Link B1AA044 ANC ECU EEPROM Data Memory Failure B1AA187 UART Communication Between ANC and Audio Amplifier Missing Message B1AA296 Front Left Microphone Circuit Component Internal Fail
Mirror Heater does not Operate with Rear Defogger Switch
DESCRIPTION When the mirror heater switch (rear window defogger switch) is operated, the mirror heater signal is sent to the air conditioning amplifier assembly and then to each outer mirror control ECU assembly via CAN communication. Based on this signal, the outer mirror control ECU assemblies ope
