Lexus ES manuals

Lexus ES: Calibration

CALIBRATION

TORQUE SENSOR ZERO POINT CALIBRATION (USING TECHSTREAM)

NOTICE:

Perform torque sensor zero point calibration if any of the following conditions occur:

  • The rack and pinion power steering gear assembly has been replaced.
  • There is a difference in steering effort between turning left and right.

(a) Perform inspection before calibration.

(1) Turn the engine switch off.

(2) Connect the Techstream to the DLC3.

(3) Turn the engine switch on (IG).

(4) Turn the Techstream on.

(5) Calibrate the rack and pinion power steering gear assembly. Enter the following menus: Chassis / EMPS / Data List.

(6) Read the Data List according to the display on the Techstream.

Chassis > EMPS > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

IG Power Supply

IG power source voltage

Min.: 0.0000 V

Max.: 20.1531 V

8 to 16 V

Engine switch on (IG)

Chassis > EMPS > Data List

Tester Display

IG Power Supply

Standard Voltage:

8 to 16 V

NOTICE:

If the IG power supply voltage is 8 V or less, calibration cannot be performed. In this case, charge or replace the battery, and then perform calibration.

(b) Perform torque sensor zero point calibration.

NOTICE:

If DTC C1516 (Torque Sensor Zero Point Adjustment Incomplete) is stored, the torque sensor zero point cannot be calibrated. Clear the DTCs before starting calibration.

(1) Align the front wheels straight ahead and center the steering wheel.

(2) Turn the engine switch off.

(3) Connect the Techstream to the DLC3.

(4) Turn the engine switch on (IG).

(5) Turn the Techstream on.

(6) Enter the following menus: Chassis / EMPS / Utility / Torque Sensor Adjustment.

Chassis > EMPS > Utility

Tester Display

Torque Sensor Adjustment

NOTICE:

  • Do not turn the steering wheel sharply.
  • During the torque sensor zero point calibration the steering wheel will shudder. Do not touch the steering wheel until at least 3 seconds have elapsed after the shuddering has stopped.

(7) Check for DTCs.

Chassis > EMPS > Trouble Codes

NOTICE:

If DTC C1515, C1516, C1534 or C1581 is output, perform troubleshooting for the corresponding DTC.

Result

See Procedure

DTC C1515 is output.

DTC C1516 is output.

DTC C1534 is output.

DTC C1581 is output.

ASSIST MAP WRITING (USING TECHSTREAM)

NOTICE:

Perform assist map writing if the following condition occurs:

The rack and pinion power steering gear assembly has been replaced.

(a) Turn the engine switch off.

(b) Connect the Techstream to the DLC3.

(c) Turn the engine switch on (IG).

(d) Turn the Techstream on.

(e) Enter the following menus: Chassis / EMPS / Utility / Signal Check.

Chassis > EMPS > Utility

Tester Display

Signal Check

HINT:

  • Follow the instructions on the Techstream to perform Signal Check.
  • With DTC C1581 output, performing Signal Check will cause the rack and pinion power steering gear assembly to enter Signal Check and the assist map will be written automatically.

(f) Wait for at least 5 seconds.

(g) Check for DTCs.

Chassis > EMPS > Trouble Codes

HINT:

After writing the assist map, if DTC C1581 is output, perform the troubleshooting procedure for DTC C1581.

Click here

READ NEXT:

 Problem Symptoms Table

PROBLEM SYMPTOMS TABLE HINT: Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of

 Terminals Of Ecu

TERMINALS OF ECU TERMINALS OF ECU *a Component without harness connected (Rack and Pinion Power Steering Gear Assembly) - - HINT: The rack and pinion power steering gear assembly uses

 Diagnosis System

DIAGNOSIS SYSTEM CHECK DLC3 (a) Check the DLC3. Click here CHECK WARNING LIGHT (a) When a problem occurs in the power steering system, the EPS warning light in the combination meter assembly comes o

SEE MORE:

 Luggage Door ECU Communication Stop Mode

DESCRIPTION Detection Item Symptom Trouble Area Luggage Door ECU Communication Stop Mode Any of the following conditions are met: Communication stop for "Back Door" is indicated on the "Communication Bus Check" screen of the Techstream. Click here Communication stop history for

 Generator Execution Torque Performance (P0E7100)

DTC SUMMARY MALFUNCTION DESCRIPTION This DTC indicates that the generator torque execution value does not correspond to the torque command value from the hybrid vehicle control ECU to the generator (MG1). The cause of this malfunction may be one of the following: Area Main Malfunction Descripti

© 2016-2024 Copyright www.lexguide.net